Applied sciences

Archives of Civil Engineering


Archives of Civil Engineering | 2016 | No 4 / II |


In order to achieve extended life of asphalt pavement, one of key points is to achieve a good bonding between it’s components. This research paper presents findings on the topic of influence of polyethylene bitumen modification on the adhesion between bitumen and aggregate. A novel method of quantifying the bitumen coated area, based on computer image analysis, has been developed for this study. Two different methods of adhesion testing were employed, namely boiling water method and the rolling bottle method. Aggregates used in this study were granite and limestone. Based on 108 measurements, it was concluded that polyethylene modification has a negative impact on binder aggregate adhesion.

Go to article


Recycling construction and demolition waste not only reduces project costs; and saves natural resources, but also solves the environmental threat caused by construction waste disposal. In this paper, C25 waste road concrete is used as an experimental material, the uniaxial compression strength and tensile splitting strength of C25 RAC whose coarse aggregate replacement rate is 0%, 25%, 50%, 75%, and 100% are tested under the condition that the water-to-cement ratio is 0.47, 0.55 and 0.61. The results show: (1) the uniaxial compression strength and tensile splitting strength decrease with the increase of RAC; (2) for concrete with the same water-to-cement ratio, when the coarse aggregate replacement rate changes from 0% to 50%, the uniaxial compression strength and tensile splitting strength of RAC changes slightly. When the coarse aggregate replacement rate changes from 50% to 100%, the uniaxial compression strength and tensile splitting strength of RAC decreases rapidly

Go to article


Assessment of the flexural buckling resistance of bisymmetrical I-section beam-columns using FEM is widely discussed in the paper with regard to their imperfect model. The concept of equivalent geometric imperfections is applied in compliance with the so-called Eurocode’s general method. Various imperfection profiles are considered. The global effect of imperfections on the real compression members behaviour is illustrated by the comparison of imperfect beam-columns resistance and the resistance of their perfect counterparts. Numerous FEM simulations with regard to the stability behaviour of laterally and torsionally restrained steel structural elements of hot-rolled wide flange HEB section subjected to both compression and bending about the major or minor principal axes were performed. Geometrically and materially nonlinear analyses, GMNA for perfect structural elements and GMNIA for imperfect ones, preceded by LBA for the initial curvature evaluation of imperfect member configuration prior to loading were carried out. Numerical modelling and simulations were conducted with use of ABAQUS/Standard program. FEM results are compared with those obtained using the Eurocode’s interaction criteria of Method 1 and 2. Concluding remarks with regard to a necessity of equivalent imperfection profiles inclusion in modelling of the in-plane resistance of compression members are presented.

Go to article


In the recent years a tendency for design of increasingly slender structures with the use of high performance concrete has been observed. Moreover, the use of high performance concrete in tunnel structures, subject to high loads with possibility of extreme loads occurrence such as fire, has an increasing significance. Presented studies aimed at improving high performance concrete properties in high temperature conditions (close to fire conditions) by aeration process, and determining high temperature impact on the concretes features related to their durability. In this paper it has been proven that it is possible to obtain high performance concretes resistant to high temperatures, and additionally that modification of the concrete mix with aerating additive does not result in deterioration of concrete properties when subject to water impact in various form.

Go to article


This paper addresses the tensile and flexural strength of HPC (high performance concrete). The aim of the paper is to analyse the efficiency of models proposed in different codes. In particular, three design procedures from: the ACI 318 [1], Eurocode 2 [2] and the Model Code 2010 [3] are considered. The associations between design tensile strength of concrete obtained from these three codes and compressive strength are compared with experimental results of tensile strength and flexural strength by statistical tools. Experimental results of tensile strength were obtained in the splitting test. Based on this comparison, conclusions are drawn according to the fit between the design methods and the test data. The comparison shows that tensile strength and flexural strength of HPC depend on more influential factors and not only compressive strength.

Go to article


The model concept, as presented in this paper, is an original solution created by the author, and can be used as a proposal to build an innovative mechanism to increase the effectiveness of programming and implementation of the development policy, and improve the quality of functioning of a building research institute. The development management system included in this model is a set of actions targeting at the effective use of human and tangible resources, undertaken in a coordinated manner and leading to the achievement of previously established objectives. The market activity of building research institutes is directly or indirectly involved in construction projects, which translates into market mechanisms, such as innovation and competitiveness. In addition, it indicates the participation of a building research institute in the engineering of construction projects as a key to entrepreneurship and implementations.

Go to article


The aim of this article is to identify opportunities for using synergies obtained by incorporation of the two methods of management: Lean Management and Agile Management on the example of the process of column concreting. Despite the seemingly contradictory assumptions the two concepts complement each other in analysed example. The strategy is based on using the idea of "one piece flow" in accordance with the Lean Management which led to a reduction of costs due to increased turnover of formwork. At the same time the success of the project resulted in a significant dependence on the ability to provide a rapid response to changing conditions during in the maturation of concrete (depending on weather conditions, which can be expected on the basis of projections having different reliability). The simultaneous use of Lean and Agile Management allowed to achieve positive results for different scenarios of environment impact on the analysed process.

Go to article


The problem of poor quality of traffic accident data assembled in national databases has been addressed in European project InDeV. Vulnerable road users (pedestrians, cyclists, motorcyclists and moped riders) are especially affected by underreporting of accidents and misreporting of injury severity. Analyses of data from the European CARE database shows differences between countries in accident number trends as well as in fatality and injury rates which are difficult to explain. A survey of InDeV project partners from 7 EU countries helped to identify differences in their countries in accident and injury definitions as well as in reporting and data checking procedures. Measures to improve the quality of accident data are proposed such as including pedestrian falls in accident statistics, precisely defining minimum injury and combining police accident records with hospital data.

Go to article


Due to different reasons a significant modal shift from railway to road transport took place over last decades. The basic reasons are pointed in the paper introduction together with contradicting transport policy taking into account environmental and economical challenges. Political vision to stimulate modal shift from road and air to railway cannot become true without achieving railway technical and operational interoperability. Paper describes wide range of technical barriers between individual intraoperable railway systems in civil engineering structures, traction power supply, control command and signalling and the ways, which are being applied to ensure stepwise converging of the technical solutions taking into account safety and technical compatibility, as well as other essential requirements, namely: reliability, accessibility, health and environment.

Go to article


In this paper we discuss the test results for concretes containing various amounts of ggbs as compared to concretes made with Portland cement. The main objective of these tests is to evaluate the influence of varying air content in such mixtures on the structure and frost resistance of concrete. The authors suggest that the approach presented here allows for a safe design of concrete mixtures in terms of their frost resistance.

The results indicate that concrete can be resistant to surface scaling even at the W/C ratio markedly higher than 0.45. Increased addition of ggbs leads to a decrease in concrete resistance to surface scaling. Proper air entrainment is the fundamental factor for frost-resistant concrete, and the air void system has to be assessed (micropore content A₃₀₀, spacing factor L). The addition of ggbs increases pore diameters, thus, to obtain the appropriate air pore spacing factor, micropore quantities introduced have to be increased.

Go to article


The possibility of construction disputes can be reduced, but they cannot be avoided due to the uncertain and risky nature of the building industry. Conflicts between construction parties often have very unfavourable effects, such as cost increases, poor construction quality and time extension in the schedule. Lots of studies have been carried out in order to try and avoid these disagreements. However, there are no common resolution tools or techniques due to the improving conditions and scope of contracted works. Advanced methods and dispute reasons should be fully monitored and updated for the applicable solutions. This paper discusses the current major constructional dispute reasons in Turkey. The questionnaire method was applied within the scope of this study. The questionnaire documents were randomly distributed to 80 contractors to analyse major dispute reasons in Turkey. Analysis of the questionnaire results indicates that the major current dispute causes are poor quality of performed works, delays in progress payments, inefficient site management, poorly written contracts and design mistakes.

Go to article


The objective of this paper is to present a probabilistic method of analyzing the combinations of snow and wind loads using meteorological data and to determine their combination factors. Calculations are based on data measured at twelve Polish meteorological stations operated by the Institute for Meteorology and Water Management. Data provided are from the years 1966 - 2010. Five combinations of snow load and 10-minute mean wind velocity pressure have been considered. Gumbel probability distribution has been used to fit the empirical distributions of the data. As a result, the interdependence between wind velocity pressure and snow load on the ground for a return period of 50 years has been provided, and the values of the combination factors for snow loads and wind actions are proposed.

Go to article

Editorial office

Henryk Zobel

Deputy Editor-in-Chief
Mariola Książek

Scientific Advisory Committee
Andrzej M. Brandt
Werner Brilon (Germany)
Jacek Chróścielewski
Luc Courard (Belgium)
Andrzej Garbacz
Andrzej Garstecki
Wojciech Gilewski
Marian Giżejowski
Oleg Kapliński
Piotr Konderla
Aleksander Kozłowski
Marian Kwietniewski
Zbigniew Młynarek
Andrzej S. Nowak (USA)
Anna Siemińska-Lewandowska
Jan Szwabowski
Waldemar Świdziński
Andrew P. Tarko (USA)
Marian Tracz
Edmundas K. Zavadskas (Lithuania)
Jerzy Ziółko

Katarzyna Orzeł



Politechnika Warszawska

Wydział Inżynierii Lądowej

Al. Armii Ludowej 16, 00-637 Warszawa, Polska Pokój 618; Telefon 22 234 62 84






Instructions for authors


1. Preparation of the paper

General: Author is responsible for the Paper contents including copyrights and text formatting. The manuscript should be written in English. It should be typed using 12 p TNR font with 1.5 line spacing, on single-sided A4 sheets with 2 cm margins. The paper should not exceed 10 pages including tables and figures plus 2 pages of an extended summary (TNR 10 pt. justify align), started from new page at the end of the manuscript. Summary in Polish for Polish natives only, others - summary in English.

The first page and the main text: The first page of the article should contain: (1) the title of the article, (2) the name, academic merits, affiliation and e-mail of each author, (3) the name and the address of the author to whom correspondence, proofs and reprints should be sent, (4) a summary of 50-150 words, (5) a list of key words (not to exceed 8). The main text should be divided into numbered (1, 2, etc.) and titled sections and, if needed, into subsections (1.1, 1.2, ... in Section 1, 2.1, 2.2, ... in Section 2, etc.). The abstract of 50-150 words is required on a separate sheet. Polish natives authors only are requested to enclose Polish translation of the abstract, others - abstract in English.

Tables and figures: Tables and figures should be inserted into the text (black-and-white figures and glossy photographs),numbered consecutively and titled. They should be referred to in the text as Fig. 1, Fig. 2, ..., Table 1, Table 2. A list of figures and tables captions (TNR 11 pt. left align, in Polish - for Polish natives only and in English) should be provided on separate sheet(s) at the end of the manuscript beforean extended summary. Colour figures will be accepted only if the colour is essential for the explanation.

Units and mathematical formulae: SI units and abbreviations are obligatory. Mathematical formulae should be typewritten and centred. The formulae referred to in the text are to be numbered consecutively in each Section, i.e. (1.1), (1.2), ... in Section 1, (2.1), (2.2), ... in Section 2, etc. The numbers should be placed in parentheses ( ) at the left margin. The formulae are to be referred to in the text as Eq. (1.1),, Eq. (1.2), ..., Eq. (2.1), Eq. (2.2), ..., etc. The formulae not referred to in the text should not be numbered.

Bibliography: References are to be listed at the end of the paper in the alphabetical order and consecutively numbered. A reference to a published paper should be referred to in the text by the last name(s) of author(s) and the reference's number in brackets [ ]. Each item should contain full bibliographical data in the format illustrated by the following examples:

[1] M. Abramowitz and I. A. Stegun, Eds. Handbook of Mathematical Functions (Applied Mathematics Series 55). Washington, DC: NBS, 1964, pp. 32-33.

[2] M. Gorkii, “Optimal design”, Dokl. Akad. Nauk SSSR, vol. 12, pp. 111-122, 1961.

(Transl.: in L. Pontryagin, Ed., The Mathematical Theory of Optimal Processes. New York: INTERSCIENCE, 1962, Ch. 2, sec. 3, pp. 127-135).

[3] B. Klaus and P. Horn, Robot Vision. Cambridge, MA: MIT Press, 1986.

[4] E. F. Moore, “Gedanken-experiments on sequential machines”, in Automata Studies

(Ann. of Mathematical Studies, no. 1), C. E. Shannon and J. McCarthy, Eds. Princeton, NJ: Princeton Univ. Press, 1965, pp. 129-153.

[5] R. L. Myer, “Parametric oscillators and nonlinear materials”, in Nonlinear Optics, vol. 4, P. G. Harper and B. S. Wherret, Eds. San Francisco, CA: Academic, 1977, pp. 47-160.

[6] L. Stein, “Random patterns”, in Computers and You, J. S. Brake, Ed. New York: Wiley, 1994, pp. 55-70.

[7] Westinghouse Electric Corporation (Staff of Technology and Science, Aerospace Div.), Integrated Electronic Systems. Englewood Cliffs, NJ: Prentice-Hall, 1970.

[8] G. O. Young, “Synthetic structure of industrial plastics”, in Plastics, vol. 3, Polymers of Hexadromicon, J. Peters, Ed., 2nd ed. New York: McGraw-Hill, 1964, pp. 15-64.

In special cases, other formats related to codes, reports, dissertations, etc. will be accepted.

Layout of the text can be downloaded from ace website:

2. Submission of the paper

Two electronic versions of the manuscript (DOC and PDF file) and License to publish should be submitted and sent directly to the Editor-in-chief by e-mail to:

Signing license agreement is required.

3. Proof read: Proofs will be sent to the corresponding author to correct any typesetting errors. Alterations to the original manuscript at this stage will not be accepted. Corrected proofs page must be mailed to the Editorial Office as soon as possible.

4. Copyright: Submission of a paper to Archives of Civil Engineering implies that the material is an original and unpublished work, not under consideration for publication elsewhere. If permission for publication of any material is required, it should be obtained from appropriate sources by the author. The corresponding author is responsible for the other authors' approval of the paper publication.

5. Reprints: The corresponding author will receive ten reprints and PDF file of the published paper free of charge.

6. Other information: Apart from research papers, other articles such as review papers, brief notes, discussions and reports may be published in the journal. Monographic papers and state-of-the-art papers are accepted after prior approval of the Editor. Reports on important conferences held in Poland may also be published. Editor decides whether the paper fulfil all requirements i.e. formal and scientific. Editor nominates two reviewers, who shall forward reviews of the accepted publication.

The paper will be published in ACE provided that the reviews are positive. If reviewers have some comments authors have to correct the paper. Papers are subject to open discussion. All letters should be addressed to the Editorial Office and will be published together with the authors' response.

7. Fees: Submission of the paper is free of charge. Submitted papers are accepted for publication after a positive opinion of two independent reviewers. When publication accepted Author will be informed by email about article processing charge incl. amount and payment deadline. ACE is non for profit and all fees are calculated to cover operational costs only. Payment is required to the following bank account:


ul. Polna 50, 00-644 WARSAW

PKO IV Department in WARSAW

Number: PL 84 1240 1053 1111 0000 0500 5707

with annotation: "Author(s) name and surname, ACE"

This page uses 'cookies'. Learn more