Applied sciences

Archives of Civil Engineering

Content

Archives of Civil Engineering | 2012 | No 2 |

Abstract

A method of detecting honeycombing damage in a reinforced concrete beam using the finite element model updating technique was proposed. A control beam and two finite element model srepresenting different severity of damage were constructed using available software and the defect parameters were updated. Analyses were performed on the finite element models to approximate the modal parameters. A datum and a control finite element model to match the datum test beams with honeycombs were prepared. Results from the finite element model were corrected by updating the Young’s modulus and the damage parameters. There was a loss of stiffness of 3% for one case, and a loss of 7% for another. The more severe the damage, the higher the loss of stiffness. There was no significant loss of stiffness by doubling the volume of the honeycombs.

Go to article

Abstract

Creep compliance of the hot-mix asphalt (HMA) is a primary input of the current pavement thermal cracking prediction model used in the US. This paper discusses a process of training an Artificial Neural Network (ANN) to correlate the creep compliance values obtained from the Indirect Tension (IDT) with similar values obtained on small HMA beams from the Bending Beam Rheometer (BBR). In addition, ANNs are also trained to predict HMA creep compliance from the creep compliance of asphalt binder and vice versa using the BBR setup. All trained ANNs exhibited a very high correlation of 97 to 99 percent between predicted and measured values. The binder creep compliance functions built on the ANN-predicted discrete values also exhibited a good correlation when compared with the laboratory experiments. However, the simulation of trained ANNs on the independent dataset produced a significant deviation from the measured values which was most likely caused by the differences in material composition, such as aggregate type and gradation, presence of recycled additives, and binder type.

Go to article

Abstract

For solving a partial different equation by a numerical method, a possible alternative may be either to use a mesh method or a meshless method. A flexible computational procedure for solving 1D linear elastic beam problems is presented that currently uses two forms of approximation function (moving least squares and kernel approximation functions) and two types of formulations, namely the weak form and collocation technique, respectively, to reproduce Element Free Galerkin (EFG) and Smooth Particle Hydrodynamics (SPH) meshless methods. The numerical implementation for beam problems of these two formulations is discussed and numerical tests are presented to illustrate the difference between the formulations.

Go to article

Abstract

The technology of recycling with foamed bitumen is a new technology of road rehabilitation. Due to the climatic conditions in the Central European countries, road pavement structure should be moisture and frost resistant. Because of its specific production conditions, this is especially important for pavements rehabilitation with the cold recycling technology. Determining the physical and mechanical properties, as well as moisture and frost resistance, depends on binder and filler contents. They are the key elements before its use for road building. The tests presented here have been performed on mineral recycled base mixes with foamed bitumen. The material from the existing layers was used. The content of bitumen binder amounted to 2.0%, 2.5%, 3.0% and 3.5%, while that of cement to 1.0%, 1.5%, 2.0%, 2.5%. The results were subject to the optimization process. This allowed to state that with the use of 2.5% foamed bitumen and 2.0% of cement, the base had the required properties, as well as the moisture and frost resistance.

Go to article

Abstract

The paper deals with application of the Gumbel model to evaluation of the environmental loads. According to recommendations of Eurocodes, the conventional method of determining return period and characteristic values of loads utilizes the theory of extremes and implicitly assumes that the cumulative distribution function of the annual or other basic period extremes is the Gumbel distribution. However, the extreme value theory shows that the distribution of extremes asymptotically approaches the Gumbel distribution when the number of independent observations in each observation period from which the maximum is abstracted increases to infinity. Results of calculations based on simulation show that in practice the rate of convergence is very slow and significantly depends on the type of parent results distribution, values of coefficient of variation, and number of observation periods. In this connection, a straightforward purely empirical method based on fitting a curve to the observed extremes is suggested.

Go to article

Abstract

Several previous investigations on failure of a certain type lattice girders railway bridge (on so called BJD line) have not convincingly explained reasons nor have they described potential hazards. This paper attempts to provide an answer, employing static, dynamic, and fatigue analysis of the structure, focusing on previously not analyzed vibrations of elements constituting a lattice node. Detailed models of two types of such nodes – damaged and non- damaged were compared, inside carefully defined limits of applicability.

Go to article

Abstract

People living in buildings may be exposed to dynamic actions. In the diagnosis and design of buildings there is an increasing need of taking into account these activities and verification of compliance of the building requirements for vibration comfort of people residing in buildings. This study presents the results of analysis of such criteria in the following standards: Polish PN-88/B-02171 [1], British BS 6472-1 [2], German DIN 4150 [3], and ISO international standards [4,5]. Basing on the results of this analysis and on the review of selected items of literature, the application of standards recommendations in diagnosis and design of buildings, as well as areas for further research on this subject is indicated. This article is an extended version of the conference paper [6] presented on the conference Urban Transport 2011.

Go to article

Editorial office

Editor-in-Chief
Henryk Zobel


Deputy Editor-in-Chief
Mariola Książek


Scientific Advisory Committee
:
Andrzej M. Brandt
Werner Brilon (Germany)
Jacek Chróścielewski
Luc Courard (Belgium)
Andrzej Garbacz
Andrzej Garstecki
Wojciech Gilewski
Marian Giżejowski
Oleg Kapliński
Piotr Konderla
Aleksander Kozłowski
Marian Kwietniewski
Zbigniew Młynarek
Andrzej S. Nowak (USA)
Anna Siemińska-Lewandowska
Jan Szwabowski
Waldemar Świdziński
Andrew P. Tarko (USA)
Marian Tracz
Edmundas K. Zavadskas (Lithuania)
Jerzy Ziółko

Secretary
Katarzyna Orzeł

Contact

 

Politechnika Warszawska

Wydział Inżynierii Lądowej

Al. Armii Ludowej 16, 00-637 Warszawa, Polska Pokój 618; Telefon 22 234 62 84

e-mail: ace@il.pw.edu.pl;

website: http://ace.il.pw.edu.pl

 

 

 

Instructions for authors

Guidelines for Authors

Template of article

License Agreement Form

Submission of articles for publication in the journal Archives of Civil Engineering should be made via the website:

https://www.editorialsystem.com/ace/

This page uses 'cookies'. Learn more