Applied sciences

Archives of Electrical Engineering

Content

Archives of Electrical Engineering | 2015 | vol. 64 | No 1 March |

Abstract

Asynchronized (doubly-fed) machines with two (three) excitating winding and reversing excitation system allow to control vector of magnetomotive force. This solution allows separating regulation of the electromagnetic torque (active power) and voltage (reactive power). This paper describes the experience in the development and operation of asynchronized turbogenerators and condensers.

Go to article

Abstract

This paper aims to present a new equivalent scheme of multi-windings traction transformers, based on multiport purely inductive circuit. The mathematical background of this equivalent scheme is described. The determination of the different scheme elements is made through a finite-elements calculation of both main and leakage inductances, for the case of a four-winding transformer. A procedure is defined, which allows to estimate the values of these elements from some measurements on the transformer at no-load and short-circuit operations. A specific strategy of short-circuit tests is described, allowing to determine all parameters in a rather simple way.

Go to article

Abstract

In this article results of diagnostic investigations of separately excited DC motor were presented. In diagnostics were applied a Fourier analysis method based on the fast Fourier transform (FFT) and a recognition method using Bayes classifier. In training process a set of the most important frequencies has been determined for which differences of corresponding signals in two states are the largest. Three categories of signals have been recognized in identification process: faultless state, state of the rotor broken one coil and state of the rotor shorted three coils

Go to article

Abstract

The paper presents selected simulation and experimental results of a hybrid ECPMS-machine (Electric Controlled Permanent Magnet Synchronous Machine). This permanent magnets (PMs) excited machine offers an extended magnetic field control capability which makes it suitable for battery electric vehicle (BEV) drives. Rotor, stator and the additional direct current control coil of the machine are analyzed in detail. The control system and strategy, the diagram of power supply system and an equivalent circuit model of the ECPMS-machine are presented. Influence of the additional excitation on the performance parameters of the machine, such as: torque, efficiency, speed limits and back-EMF have also been discussed.

Go to article

Abstract

In this paper the mathematical model of the brushless DC motor (BLDCM) with a double 3-phase stator winding is analysed. Both the 3-phase windings are mutually displaced by 30 electrical degree. Special care has been sacrificed to influence of higher harmonics of induced electromotive forces (EMF) on electromagnetic torque and zero sequence voltages that may be used for sensorless control. The mathematical model has been presented in natural variables and, after transformation to symmetrical components, in a vector form. This allows, from one side, for formulating the equivalent circuit suitable for circuit oriented simulators (e.g.: Spice, SimPowerSystems of Simulink) and, from the other point of view, for analysis of higher harmonics influence on control possibilities. These considerations have been illustrated with some results of four quadrant operation obtainded due to simulation at automatic control.

Go to article

Abstract

This paper deals with detection of the stator windings shorted turns in an induction motor drive working under open (scalar) and closed loop (Direct Field Oriented DFO) control structures. In order to detect the early stage of stator winding fault, the analysis of symmetrical and principal components of stator voltages and currents is used. Experimental results obtained from a specially prepared induction motor are presented.

Go to article

Abstract

Magnetic measurements, carried out by means of the Epstein frame, have shown that most typical dynamo steel sheets have certain anisotropic properties. In numerical analysis, anisotropic properties are taken into account with the use of the special function of the grain distribution in the given dynamo sheet. For engineering purposes, it is desirable to assess the influence of these properties on the changes of the magnetic flux density in typical dynamo steel sheets, especially during the rotational magnetization. For this purpose, measurements of the flux density changes and field strength changes in the circular-shaped samples of two selected typical dynamo sheets were performed. These measurements were carried out for several values of the current flowing in windings which generated the axial or rotational magnetic field in the test dynamo sheet. The influence of the magnetic anisotropy on the magnetization process was briefly discussed for both types of the magnetization processes.

Go to article

Abstract

The paper is a presentation of an analysis concerning performance of a 12/8 dual-channel switched reluctance motor (DCSRM). Formulas constituting a base for a non-linear mathematical model of DCSRM are presented. Simulation and laboratory tests were carried out for the motor operating in the dual-channel and single-channel mode. The results of the field theory-based calculations are presented in the form of fluxes in individual phases expressed as functions of currents and a rotor position angle. The results of the computer simulations are shown as the static characteristics of fluxes and the torque as well as voltage, current, and torque waveforms. The results of the laboratory tests are also presented.

Go to article

Abstract

Lately, there has been increased interest in hybrid excitation electrical machines. Hybrid excitation is a construction that combines permanent magnet excitation with wound field excitation. Within the general classification, these machines can be classified as modified synchronous machines or inductor machines. These machines may be applied as motors and generators. The complexity of electromagnetic phenomena which occur as a result of coupling of magnetic fluxes of separate excitation systems with perpendicular magnetic axis is a motivation to formulate various mathematical models of these machines. The presented paper discusses the construction of a unipolar hybrid excitation synchronous machine. The magnetic equivalent circuit model including nonlinear magnetization curves is presented. Based on this model, it is possible to determine the multi-parameter relationships between the induced voltage and magnetomotive force in the excitation winding. Particular attention has been paid to the analysis of the impact of additional stator and rotor yokes on above relationship. Induced voltage determines the remaining operating parameters of the machine, both in the motor and generator mode of operation. The analysis of chosen correlations results in an identification of the effective control range of electromotive force of the machine.

Go to article

Abstract

The calculations results of the temperature distribution in a 3-phase transformer with modular amorphous core are presented. They were performed for two frequency values which were higher than the power system one. For the 3D field analyses the Finite Element Method (FEM) was used. The calculated temperature at the points of the core surface has been verified using an infrared camera.

Go to article

Abstract

This paper presents a methodology for the calculation of the flux distribution in power transformer cores considering nonlinear material, with reduced computational effort. The calculation is based on a weak coupled multi-harmonic approach. The methodology can be applied to 2D and 3D Finite Element models. The decrease of the computational effort for the proposed approach is >90% compared to a time-stepping method at comparable accuracy. Furthermore, the approach offers a possibility for parallelisation to reduce the overall simulation time. The speed up of the parallelised simulations is nearly linear. The methodology is applied to a single-phase and a three-phase power transformer. Exemplary, the flux distribution for a capacitive load case is determined and the differences in the flux distribution obtained by a 2D and 3D FE model are pointed out. Deviations are significant, due to the fact, that the 2D FE model underestimates the stray fluxes. It is shown, that a 3D FE model of the transformer is required, if the nonlinearity of the core material has to be taken into account.

Go to article

Abstract

This paper presents the optimal sizing of PV/Wind/Fuel Cell/Battery Hybrid Energy System for energizing a Small Scale Industrial Application or a village domestic load of 200 kW. HOMER software is used for simulation of the complete system. The solar radiation data and wind speed data used in this paper are for the place of Coimbatore, Tamil Nadu, India which is located 11.0183° N longitude and 76.9725° E latitude. The optimized sizes of components of Hybrid Power System (HPS) are found based on Levelised Cost of Energy (LCE) and total Net Present Cost (NPC). The results are presented and compared for five different combinations of HPS components. Suggestions are also presented to choose the low cost system which produces energy at low LCE.

Go to article

Abstract

This original paper deals with a new approach for the study of behavior in nonlinear regime of a new three-phase high voltage power supply for magnetrons, used for the microwave generators in industrial applications. The design of this system is composed of a new three-phase leakage flux transformer supplying by phase a cell, composed of a capacitor and a diode, which multiplies the voltage and stabilizes the current. Each cell. in turn, supplies a single magnetron. An equivalent model of this transformer is developed taking into account the saturation phenomenon and the stabilization process of each magnetron. Each inductance of the model is characterized by a non linear relation between flux and current. This model was tested by EMTP software near the nominal state. The theoretical results were compared to experimental measurements with a good agreement. Relative to the current device, the new systemprovides gains of size, volume, cost of implementation and maintenance which make it more economical.

Go to article

Editorial office

Editor-in-Chief
Professor Andrzej Demenko, Poznan University of Technology, Poland

Deputy/ Managing Editor
Mariusz Barański, Ph.D., Poznan University of Technology, Poland
Łukasz Knypiński, Ph.D., Poznan University of Technology, Poland

Editorial Advisory Board
Chairman: Marian P. Kaźmierkowski, Warsaw, Poland
Secretary: Mariusz Jagieła, Opole, Poland

Members professors:
Anouar Belahcen, Espoo, Finland

Frede Blaabjerg,Aalborg, Denmark

Ion Boldea,Timisoara, Romania

Herbert De Gersem,Darmstadt, Germany

Jacek Gieras, Rockford, USA

Kay Hameyer, Aachen, Germany

Marian K. Kazimierczuk, Dayton, USA

Stefan Kulig, Dortmund, Germany

David A. Lowther, Montreal, Canada

Jacek Marecki, Gdańsk, Poland

Zhuoxiang Ren, Paris, France

José Rodríguez Pérez,Valparaíso, Chile

Ryszard Sikora, Szczecin, Poland

Zbigniew Styczyński, Magdeburg, Germany

Jan Sykulski, Southampton, UK

Sławomir Wiak, Łódź, Poland

 

Language Editor

Krystyna Guzek

Statistical Editor

Mariusz Barański, Poznan, Poland
Poznan University of Technology

Theme Editors

Jerzy Barglik, Gliwice, Poland
Professor at Silesian University of Technology

Zbigniew Lubosny, Gdansk, Poland
Professor at Gdańnk University of Technology

Marian Łukaniszyn, Opole, Poland
Professor at Opole University of Technology

Marian Pasko, Gliwice, Poland
Professor at Silesian University of Technology

Stanisław Piróg, Krakow, Poland
Professor at AGH University of Science and Technology

Henryka Danuta Stryczewska, Lublin, Poland
Professor at Lublin University of Technology

Jan Sykulski, Southampton, UK
Professor at University of Southampton

Adam Szelag, Warsaw, Poland
Professor at Warsaw University of Technology

Romulad Włodek, Krakow, Poland
Professor at AGH University of Science and Technology

Technical Editor :

Typesetting in LATEX: Drukarnia Braci Grodzickich Sp.j., 05-500 Piaseczno, ul. Geodetów 47a, Poland

Contact

All contributions should be addressed to the Editor-in-Chief or the Editorial Office:

Address of the Editorial Office:

Archives of Electrical Engineering
Piotrowo 3A (Room 612X)
60-965 Poznan, Poland
tel: (48-61) 665-26-36
fax: (48-61) 665-23-81
e-mail: aee@put.poznan.pl

Website: www.aee.put.poznan.pl

Instructions for authors

ARCHIVES OF ELECTRICAL ENGINEERING (AEE) (previously Archiwum Elektrotechniki), quarterly journal of the Polish Academy of Sciences is OpenAccess, publishing original scientific articles and short communiques from all branches of Electrical Power Engineering exclusively in English. The main fields of interest are related to the theory & engineering of the components of an electrical power system: switching devices, arresters, reactors, conductors, etc. together with basic questions of their insulation, ampacity, switching capability etc.; electrical machines and transformers; modelling & calculation of circuits; electrical & magnetic fields problems; electromagnetic compatibility; control problems; power electronics; electrical power engineering; nondestructive testing & nondestructive evaluation.,

Manuscript submission:

All manuscripts should be submitted electronically on Editorial System.

Submission of paper to the Archives of Electrical Engineering is understood to imply that the article is original, unpublished and is not being considered for publication elsewhere. All articles will be reviewed. Since 2013, Authors wishing to use the facility of colour printing should consult the editors.,

Template:

Microsoft Word is recommended as a standard word processor to prepare the paper to the AEE journal. If you use the LaTex format, please transfer your document to Microsoft Word and then use Template AEE.
Please use Template AEE to prepare your paper.

,

The reviewing process:

Each paper submitted for publication in Archives of Electrical Engineering is subjected to the following review procedure:
a) the paper is reviewed by the editor in chief or guest editor for general suitability for publication in AEE
b) if it is judged suitable two reviewers are selected and a double blind peer review process takes place
c) based on the recommendations of the reviewers, the editor then decides whether the paper should be accepted in its present form, revised or rejected
d) the author(s) is(are) informed by e-mail on the results of the reviewing procedure.
The papers are published on average within 3 months after acceptance.,

Requirements for preparation of manuscripts:

The manuscripts submitted for publication should not exceed 21 000 characters (ca. 12 pages of a manuscript written on an A4 sheet in Times New Roman, 10pt font size, single line spacing and 3.8 cm margins). The manuscripts, written in UK English, should be typed using Template AEE according to the following instructions and should include: a title page with the title of a manuscript, a short title; abstract; key words, text; list of references. A DOI number as well as received and revised data will be completed by Editor. When you open Template.doc, select "Print Layout" from the "View" menu in the menu bar (View > Print Layout). Then type over sections of Template.doc or cut and paste from another document and then use markup styles (Home > Styles). For example, the style at this point in the document is "main text").

All papers submitted for publication are assessed on the basis of the mutual anonymity rule as to the names of reviewers and authors. Authors' names and affiliations should not appear in the attached text/tables/figures.

If English is not your first language, ask an English-speaking colleague to proofread your manuscript. The manuscripts that fail to meet basic standards of literacy are likely to be immediately declined or after the language assessment, sent to the authors for linguistic improvement.

The manuscripts are published on average within 3 months after their acceptance.

Do not change the font sizes or line spacing to squeeze more text into a limited number of pages. Leave some open space around your figures.

The AEE journal publishes an ORCID for all authors. You will need a registered ORCID in order to submit your paper for peer review. ORCID registration is free and only takes a minute. Please note that ORCIDs will be added in the course of the author's proofreads.

,

Text:

The pages must be numbered consecutively. Articles should be divided into numbered sections, and if necessary subsections, preferably: Introduction, Material, Methods, Results, Conclusion and References. Any special characters (e.g. Greek, script, etc.) should be named in the margin where the character first occurs in the text. Names of species are to be accentuated with wavy underlining (italics). Equations should be numbered serially (1), (2), ... on the right side of the page. Footnotes should be avoided, if required, they should be used only for brief notes which do not fit well into the text. Figures and tables have to be included into the text. If table is typed on a separate page its position in the text should be marked. Abbreviations should be explained when they first appear in the text.,

Math:

Please use the Microsoft Equation 3.0 editor (comes with Microsoft Office 2007 and later versions) or the MathML editor as well as MathType editor to build an equation in your manuscript.
To insert an equation in Word, choose Insert, then Object. This will bring up a dropdown menu, where the Object option should be chosen again. Pressing it opens a popup window, where the Create New option has to be clicked. Scrolling down the window allows to find Microsoft Equation 3.0.

,

Equations:

Equations should be typed within the text, centred, and should be numbered consecutively throughout the text. Their numbers should be typed in parentheses, flush right. Equations should be referred to in text, e.g. (1), except at the beginning of a sentence: "Equation (1) is ...". All symbols appearing in equations have to be defined in the text, before or just after the equation.
If the symbols are written in Times New Roman use italic fonts. Symbols of vectors and matrices should be written in bold fonts. Do not italicize Greek fonts and mathematical symbols like e.g.: the derivative symbol d, max, min, etc. The indices of symbols that are indices themselves should be written in a clear manner.
Note that the equation is centered using a center tab stop. Please keep the same font in the formulas and text.,

Unit Symbols, Abbreviations:

Define abbreviations and acronyms the first time they are used in the text, even after they have been defined in the abstract. Abbreviations such as IEEE, SI, MKS, CGS, sc, dc, and rms do not have to be defined. Do not use abbreviations in the title or heads unless they are unavoidable.
Si units are recommended for use in formulas, drawings and tables., for example the SI unit for magnetic field strength H is A/m. Apply the center dot to separate compound units.
Do not mix complete spellings and abbreviations of units: "Wb/m2" or "webers per square meter," not "webers/m2." Spell units when they appear in text: "...a few henries…", not "...a few H…".
Use a zero before decimal points: "0.25," not ".25." Use "cm3," not "cc."
Unit Symbols, SI Prefixes as well as Abbreviations should be writing in accordance with the IEEE standard,

Tables, figures (illustrations) and captions:

The illustrations (line diagrams and photographs) should be suitable for direct reproduction. The lettering as well the details should have proportional dimensions to maintain their legibility after the usual reduction. All illustrations should be numbered consecutively (Fig. X). Tables are numbered with Arabic numerals.
All figures, figure captions, and tables in the text must be inserted into the correct places.
Figures, photos, tables or other parts of a manuscript that have previously appeared in another publication or are not the property of the authors must be properly acknowledged in the manuscript. Permission to republish these items must be obtained by the corresponding author from a person or institution holding the copyright, usually the publisher.
Authors are requested to send figures (diagrams, line drawings and photographic images) in separate computer files. JPG, PNG or TIF are the recommended file formats. Photographs, colour and greyscale figures should be at least at a resolution of 400dpi. Linear, including tables should be at a minimum of 600dpi.
All colour figures should be generated in the RGB or CMYK colour space, while greyscale images in the greyscale colour space.
When preparing your figures/graphics etc., we suggest the use of the Arial 8 point font for axis numbers and Arial 9 point font for axis names. Figures/graphics etc. can be prepared in one of two proposed ways - see Template AEE.
Tables are numbered with Arabic numerals. Use 9 point Times New Roman for the title of the table and 9 point Times New Roman for the filling of the table (9 in the case of symbols with subscripts).
AEE journal allows an author to publish color figures in e-version at no charge, and automatically convert them to grayscale for print versions. Authors wishing to use the facility of color printing should consult the editors.,

Conclusions:

A conclusion might elaborate on the importance of the work or suggest applications and extensions. Although a conclusion may review the main points of the manuscript, do not replicate the abstract as the conclusion.,

References:

References in text must be numbered consecutively by Arabic numerals placed in square brackets. Please make sure that you use full names of journals i.e. Archives of Electrical Engineering. Please ensure that all references in the Reference list are cited in the text and vice versa.
Please provide name(s) and initials of author(s), the title of the manuscript, editors (if any), the title of the journal or book, a volume number, the page range, and finally the year of publication in brackets.
You can use the rules presented on the site: IEEE standard

Examples of the ways in which references should be cited are given below:

Journal manuscript
[1] Author1 A., Author2 A., Title of paper, Title of periodical, vol. x, no. x, pp. xxx-xxx (YEAR).
example
[1] Steentjes S., von Pfingsten G., Hombitzer M., Hameyer K., Iron-loss model with consideration of minor loops applied to FE-simulations of electrical machines, IEEE Transactions on Magnetics. vol. 49, no. 7, pp. 3945-3948 (2013).
[2] Idziak P., Computer Investigation of Diagnostic Signals in Dynamic Torque of Damaged Induction Motor, Electrical Review (in Polish), to be published.
[3] Cardwell W., Finite element analysis of transient electromagnetic-thermal phenomena in a squirrel cage motor, submitted for publication in IEEE Transactions on Magnetics.

Conference manuscript
[4] Author A., Title of conference paper, Unabbreviated Name of Conf., City of Conf., Country of Conf., pp. xxx-xxx (YEAR).
example
[4] Popescu M., Staton D.A., Thermal aspects in power traction motors with permanent magnets, Proceedings of XXIII Symposium Electromagnetic Phenomena in Nonlinear Circuits, Pilsen, Czech Republic, pp. 35-36 (2016).

Book, book chapter and manual
[5] Author1 A., Author2 A.B., Title of book, Name of the publisher (YEAR).
example
[5] Zienkiewicz O., Taylor R.L., Finite Element method, McGraw-Hill Book Company (2000).

Patent
[6] Author1 A., Author2 A., Title of patent, European Patent, EP xxx xxx (YEAR).
example
[6] Piech Z., Szelag W., Elevator brake with magneto-rheological fluid, European Patent, EP 2 197 774 B1 (2011).

Thesis
[7] Author A., Title of thesis, PhD Thesis, Department, University, City of Univ. (YEAR).
example
[7] Driesen J., Coupled electromagnetic-thermal problems in electrical energy transducers, PhD Thesis, Faculty of Applied Science, K.U. Leuven, Leuven (2000).

For on electronic forms
[8] Author A., Title of article, in [Title of Conference, record as it appears on the copyright page], [copyright year] © [applicable copyright holder of the Conference Record]. doi: [DOI number].
example
[8] Kubo M., Yamamoto Y., Kondo T., Rajashekara K., Zhu B., Zero-sequence current suppression for open-end winding induction motor drive with resonant controller, in IEEE Applied Power Electronics Conference and Exposition (APEC), © APEC, 2016, doi: 10.1109/APEC.2016.7468259

Website
[9] http://www.aee.put.poznan.pl, accessed April 2010.,

Proofs:

Authors will receive proofs for correction, which should be returned promptly. All joint contributions must indicate the name and address of the authors to whom proofs should be sent.,

Fees for printing the papers in AEE:

AEE is published in Open Access, which means that all our articles on the Internet are available for readers free of charge, however it is requested that the authors pay an article-processing charge (reviewing, editing, proofreading, checking for plagiarism, distribution and so on) in order for their articles to be published and made freely available online immediately on publication.
The fee for the publication of an article in the AEE journal is 210 Euro.,

Abstracting & Indexing:

Archives of Electrical Engineering is covered by the following services:

  • Arianta
  • Baidu Scholar
  • BazTech
  • Celdes
  • CNKI Scholar (China National Knowledge Infrastucture)
  • CNPIEC
  • DOAJ
  • EBSCO - TOC Premier
  • EBSCO (relevant databases)
  • EBSCO Discovery Service
  • Elsevier - Compendex
  • Elsevier - Engineering Village
  • Elsevier - SCOPUS
  • Genamics JournalSeek
  • Google Scholar
  • ICI Journals Master List
  • Inspec
  • J-Gate
  • Naviga (Softweco)
  • POL-Index
  • Primo Central (ExLibris)
  • ProQuest - Advanced Technologies Database with Aerospace
  • ProQuest - Electronics and Communications Abstracts
  • ProQuest - Engineering Journals
  • ProQuest - High Tech Research Database
  • ProQuest - Illustrata: Technology
  • ProQuest - SciTech Journals
  • ProQuest - Technology Journals
  • ProQuest - Technology Research Database
  • SCImago (SJR)
  • Summon (Serials Solutions/ProQuest)
  • TDOne (TDNet)
  • TEMA Technik und Management
  • Thomson Reuters - Emerging Sources Citation Index
  • Ulrich's Periodicals Directory/ulrichsweb
  • WorldCat (OCLC)
,

Open Access policy

Archives of Electrical Engineering jest czasopismem wydawanym w wolnym dostępie na licencji CC BY-NC-ND 4.0.

Archives of Electrical Engineering is an open access journal with all content available with no charge in full text version. The journal content is available under the licencse CC BY-NC-ND 4.0.

This page uses 'cookies'. Learn more