In this work, numerical modeling of steady state heat and mass transfer is presented. Both laminar and hydrodynamically fully developed turbulent flow in a pipe are shown. Numerical results are compared with values obtained from analytical solution of such problems. The problems under consideration are often denoted as extended Graetz problems. They occur in heat exchangers using liquid metals as working fluid, in cooling systems for electric components or in chemical process lines. Calculations were carried out gradually decreasing the mesh size in order to examine the convergence of numerical method to analytical solution.
The Bulletin of the Polish Academy of Sciences: Technical Sciences (Bull.Pol. Ac.: Tech.) is published bimonthly by the Division IV Engineering Sciences of the Polish Academy of Sciences, since the beginning of the existence of the PAS in 1952. The journal is peer‐reviewed and is published both in printed and electronic form. It is established for the publication of original high quality papers from multidisciplinary Engineering sciences with the following topics preferred: Artificial and Computational Intelligence, Biomedical Engineering and Biotechnology, Civil Engineering, Control, Informatics and Robotics, Electronics, Telecommunication and Optoelectronics, Mechanical and Aeronautical Engineering, Thermodynamics, Material Science and Nanotechnology, Power Systems and Power Electronics. Journal Metrics: JCR Impact Factor 2018: 1.361, 5 Year Impact Factor: 1.323, SCImago Journal Rank (SJR) 2017: 0.319, Source Normalized Impact per Paper (SNIP) 2017: 1.005, CiteScore 2017: 1.27, The Polish Ministry of Science and Higher Education 2017: 25 points. Abbreviations/Acronym: Journal citation: Bull. Pol. Ac.: Tech., ISO: Bull. Pol. Acad. Sci.-Tech. Sci., JCR Abbrev: B POL ACAD SCI-TECH Acronym in the Editorial System: BPASTS.
This paper deals with wastewater treatment systems placed in motorway service areas (MSAs). In the years 2008-2009 eight of such facilities installed on the stretch of the A2 motorway between Poznań and Nowy Tomyśl were examined and analyzed. The system consists of a septic tank, a submerged aerated biofilter and an outflow filter. The volume of traffic on the highway was analyzed, the amount of water use was measured and peak factors were calculated. On this basis it was concluded that the inflows to the wastewater treatment systems in many cases exceeded the nominal design values. Based on the analysis of effluent quality it was found that the effects of plant operation in large part did not meet the requirements. It was found that the bioreactor aeration system and the design of the suspension separator (outflow filter) should be modified. One of the solutions was to use the soil-reed bed for wastewater treatment. The treatment of wastewater from the MSAs is a task that must take into account the unusual character of these facilities and the atypical quality of the effluent.
This paper reports the results of an analysis of indicators describing the effectiveness of actions taken and repairs made by the maintenance services in a food industry company which had implemented a new manufacturing execution system (MES) 10 months prior to the study. The application of the above effectiveness indicators plays a significant role in the rationalization of functioning of maintenance services. Therefore, it is vital that they are calculated correctly and interpreted in a way that has a positive effect on the organization of maintenance works. The paper investigates four effectiveness indicators employed by the maintenance services of the company in question, i.e., mean time to failure (MTTF), mean time between failures (MTBF), mean time to repair (MTTR) and overall equipment effectiveness (OEE). The objective of the analysis was to verify the correctness of determination of the above indicators in the analysed company. In addition, the study was to determine whether the use of correctly determined indicators and results interpretation could lead to a higher effectiveness of the actions taken by the maintenance services department. Moreover, the paper presents a diagnosis of problems connected with incorrect determination and visualization of the above-mentioned indicators in the analysed company.
The paper presents the results of the effect of isothermal heating time on the disappearance of strain hardening (the softening degree) of the studied high-manganese TRIPLEX type steels at a temperature of 900 and 1000°C. In order to determine the kinetics of recrystallization of austenite plastically deformed for selected steels, hot compression tests with draft ε = 0.2 were made. The presented results reveal that the complete recrystallization of austenite needs long isothermal heating times. In industrial conditions, such long times are not used, therefore in the initial rolling passages, the time required for half recrystallization of austenite t0.5 is often used. The total disappearance of the strain hardening, completion of the recrystallization of austenite tested high-manganese X98 and X105 TRIPLEX type steels isothermal heating time requires far more than 200 s. The increase of the deformation temperature is a factor influencing the acceleration of the disappearance of strain hardening.
Animals as a source of organs and tissues for xenotransplantation could become a backup solution for the growing shortage of human donors. The presence of human xenoreactive anti- bodies directed against Galα1,3Gal antigens on the cell surface of a pig donor triggers the activa- tion of the complement leading to a hyperacute reaction. The development of genetic engineer- ing techniques has enabled the modification of genomes by knocking in and/or knocking out genes. In this paper, we report the generation of modified pigs with ZFN mediated disruption of the GGTA1 gene encoding the enzyme responsible for synthesis of Galα1,3Gal antigens. ZFN plasmids designed to target the exon 9 region of the pig GGTA1 gene encoding the catalytic domain were injected into the pronuclei of fertilized egg cells. Among 107 piglets of the F0 gene- ration analyzed, one female with 9-nt deletion in exon 9 of the GGTA1 gene was found. 13 of 33 piglets of the F1 generation represented the +/- GGTA1 genotype and 2 of 13 F2 piglets repre- sented the -/- GGTA1 genotype. No changes in the animals’ behavior, phenotype or karyotype were observed. Analysis confirmed heredity of the trait in all animals. A complex functional analysis of the modified animals, including flow cytometry, human serum cytotoxicity test and immunohistochemical detection, was performed to estimate the phenotype effect of genetic modification and this indicated an efficient GGTA1 knock-out in modified pigs.
Lacydonia (Polychaeta: Phyllodocida) is a poorly known genus containing 16 species that are sporadically collected in low densities all over the world oceans. During three cruises (in June 2014 in Ullsfjorden, northern Norway, in January 2015 in Kongsfjorden, and in June 2012 in Smeerenburg, Svalbard) nine specimens of Lacydonia eliasoni were found on sandy and muddy sediments at depths from 180 to 350 m. All specimens were incomplete and consisted of 10 to 29 chaetigers. This study presents the first record of the Lacydonia genus in the waters of Svalbard as well as the first record of L. eliasoni in coastal waters off northern Norway. This species has been reported previously in the Skagerrak and Trondheimsfjorden (southern Norway), our findings therefore may indicate a northward extension of its range, possibly due to climate changes.
Materials and their development process are highly dependent on proper experimental testing under wide range of loading within which high-strain rate conditions play a very significant role. For such dynamic loading Split Hopkinson Pressure Bar (SHPB) is widely used for investigating the dynamic behavior of various materials. The presented paper is focused on the SHPB impulse measurement process using experimental and numerical methods. One of the main problems occurring during tests are oscillations recorded by the strain gauges which adversely affect results. Thus, it is desired to obtain the peak shape in the incident bar of SHPB as “smooth” as possible without any distortions. Such impulse characteristics can be achieved using several shaping techniques, e.g. by placing a special shaper between two bars, which in fact was performed by the authors experimentally and subsequently was validated using computational methods.