The results of the efficiency of the primary reclamation process as well as the influence of the used sand temperature and other process parameters on it are presented in this paper. A separate stand realized on a reduced scale was built, which is an analogous process of the primary reclamation treatment of spent foundry sands. The used sands were introduced to the crushing process in an agglomerated form in the way typically used in industrial devices. The primary reclamation process was realized on a set of four horizontal sieves with decreasing mesh clearances while maintaining their geometrical dimensions applied in the Regmas industrial device. The model system consists of a vibratory drive mounted on the table, allowing us to control the supply frequency of the vibratory motors within a range of 40-60 Hz as well as the computer system for measuring the vibration parameters and drive power. The used sand on the quartz matrix with the KALTHARZ U404 resin and 100T3 hardener was used in our investigations. The used sand was prepared under the following conditions: cubic-shaped elements made of the applied furan sand was compacted by vibrations then hardened and subjected to heating under controlled conditions (as a “simulation” of the overheating process taking place in the mold after pouring). Time functions of the crushing and sieving process in dependence of the overheating degree of the reference sand samples (100°, 200°, and 300°C) were investigated at various table vibration frequencies and feed loads of the sieve set. The relative index of the crushing ability was determined.
The investigation results of the reclamation of spent moulding sands with furfuryl resin are presented in this paper. The reclamation process was performed in the secondary reclamation chamber of the REGMAS 1.5 vibratory reclaimer. 70 kg portions of moulding sands, previously subjected to the primary reclamation and dedusting, were used. The secondary reclamation was performed in two stages: the first consisted of determining the reclaimer intensity at various reclamation times (5 min, 10 min and 15 min) and various electrovibrator frequencies (40 Hz, 50 Hz and 60 Hz), the second consisted of determining the influence of additional crushing elements on the intensity of processes.
The article presents the results of selected energy parameters calculations, carried out for the recorded values of instantaneous voltages and currents in the three-phase power supply of the model vibratory unit. The parameters were the values of active and apparent power taken from the drive consisting of two electric motors supplied by the inverter for selected frequency settings and directly from the power grid. In addition, calculations of tgφ power factor values were made to evaluate the compensation of reactive power consumption in the tested power systems. Measurements and calculations lead to the conclusion that if the frequency of the inverter output voltage rises, the active and apparent power consumed by the model vibratory drive unit increases. The active and apparent power for setting the output frequency of the inverter from 50 Hz was less than the active and apparent power taken by the model vibratory unit that was powered directly from the power grid. The power factor tgφ in the power supply system was approximately 6, except one case (f = 30 Hz).
The paper, especially dealt with problems of reclamation of used furan sand, carried out in new, vibratory sand reclamation unit REGMAS developed by researches from AGH-University of Science and Technology, Faculty of Foundry Engineering in Cracow (Poland). Functional characteristics of reclamation unit as well as the results of reclamation of used sand with furfuryl resin are discussed in the paper. The quality of reclaim was tested by means of the LOI and pH value, dust content in the reclaim and at least by the the quality of the castings produced in moulds prepared with the use of reclaimed matrix.
The cumulative results of investigations of the possibility of using the reclaimed materials after the mechanical, thermal or mechanical-thermal reclamation for making cores by means of the blowing method in the alkaline CO2 technology, are presented in the paper. Three kinds of spent sands: with furfuryl resin, bentonite and alkaline phenolic resin, obtained from the foundry, were subjected to three kinds of reclamation: mechanical, thermal and combined mechanical-thermal, applying for this aim adequate experimental devices. The obtained reclaims were assessed with regard to the degree of the matrix liberation from the determined binding material. Reclaims of moulding sands with binders of the form of resin were assessed with regard to ignition loss values and pH reaction, while reclaims of moulding sands with bentonite with regard to the residual clay content and pH value. In all cases the results of the performed sieve analyses were estimated and the average characteristic diameter dl was determined. The reclaimed matrix was applied as a full substitute of the fresh high-silica sand in typical procedures of preparing core sands used for making shaped samples for bending strength investigations, Rg u .
The investigation results of the mechanical reclamation of spent moulding sands from the Cordis technology are presented in the paper. The quality assessment of the obtained reclaim and the influence of the reclaim fraction in a matrix on the core sand strength is given. The reclaim quality assessment was performed on the basis of the determination of losses on ignition, Na2O content on reclaim grains and pH values. The reclaim constituted 100%, 75% and 50% of the core sand matrix, for which the bending strength was determined. The matrix reclamation treatment was performed in the experimental rotor reclaimer RD-6. Spent sands were applied in as-delivered condition and after the heating to a temperature of 140 o C. Shaped samples for strength tests were made by shooting and hardening of sands in the warmbox technology.
The effects of filling the core box cavity and sand compaction in processes of core production by blowing methods (blowing, shooting) depend on several main factors. The most important are: geometrical parameters of cavity and complexity of its shape, number, distribution and shape of blowing holes feeding sands as well as the venting of a technological cavity. Values of individual parameters are selected according to various criteria, but mostly they should be adjusted to properties of the applied core sand. Various methods developed by several researchers, including the authors own attempts, allow to assess core sands properties on the basis of special technological tests projecting the process into a laboratory scale. The developed criteria defining a degree or a filling ability factor provide a better possibility of assessing the core sand behavior during flowing and core box filling, which indicate the value and structure of the obtained compacting decisive – after hardening – for strength and permeability. The mentioned above aspects are analyzed – on the basis of authors’ own examinations - in the hereby paper.
Theoretical problems concerning the determination of work parameters of the two-phase sand-air stream in the cores making process by blowing methods as well as experimental methods of determination of the main and auxiliary parameters of this process decisive on the cores quality assessed by the value and distribution of their apparent density are presented in the paper. In addition the results of visualisations of the core-box filling with the sand-air stream, from the blowing chamber, obtained by the process filming by means of the quick-action camera are presented in the paper and compared with the results of simulation calculations with the application of the ProCast software.