The magnetic properties of the U-type ferrite synthesized by a sol-gel process had studied by substituting cobalt with manganese or zinc in cobalt-based U-type ferrite. The substituted U-type ferrite showed a dominant crystal structure at a different substitution ratio of manganese and zinc. The change of the starting temperature of U-type ferrite formation according to substitutional elements was confirmed by TG-DTA analysis. In the case of manganese substitution, the starting temperature of U-type ferrite formation lowered, and on the contrary, when zinc was substituted, it became higher. The magnetic properties of the U-type ferrite substituted with manganese showed a tendency that the saturation magnetization was decreased and the coercivity was increased as the manganese ratio increased. The highest saturation magnetization was 57.9 emu/g in the specific composition (Ba4Co0.5Zn1.5Fe36O60) substituted with zinc.
Weld metal deposit (WMD) was carried out for standard MMA welding process. This welding method is still promising mainly due to the high amount of AF (acicular ferrite) and low amount of MAC (self-tempered martensite, retained austenite, carbide) phases in WMD. That structure corresponds with good impact toughness of welds at low temperature. Separate effect of these elements on the mechanical properties of welds is well known, but the combined effect of these alloy additions has not been analyzed so far. It was decided to check the total influence of nickel with a content between 1% to 3% and molybdenum with content from 0.1% up to 0.5%.
Repeated austenitisation and furnace cooling of homogenised 0.16 wt. % carbon steels result in ferrite grain sizes between 27 μm and 24 μm. Similarly, repeated austenitisation and normal-air cooling produces ferrite grain sizes between 17 μm and 12 μm; while repeated austenitisation and forced-air cooling produces a minimum grain size of 9.5 μm. Furnace cooling decomposes the austenite eutectoidally to lamellar pearlite; while normal-air cooling and forced-air cooling after austenitisation cause degeneration of pearlite regions producing grain boundary network as well as cluster of cementite and other carbides. Forced-air cooled samples provide the highest YS (364 MPa) and UTS (520 MPa); while furnace cooling provides the lowest (290 MPa and 464 MPa) leaving the normal-air cool performance in between. Hardness values depict the role of individual ferrite and pearlite content and the extent of pearlite degeneration occurring after each cyclic treatment.
In this study, BaFe12-2xCoxTixO19 (X : 0 to 2.0, 0.2) powders were synthesized by sol-gel process. TG-DTA, XRD, SEM, VSM, and Network analyzer were measured in order to influence easy magnetization axis change on the wave absorption frequency range change. The easy magnetization axis change of the annealed powder at 900°C and 1200°C was confirmed by the coercive force decreased 4,800 and 3,870 Oe to 260 and 269 Oe, respectively, at the substitution ratio of 0.8 and 1.0. And it was confirmed that the change of the easy magnetization axis affected the change of the wave absorption frequency. The wave absorption frequency of substituted Barium Ferrite was less than 10 GHz range after the easy magnetization axis of Barium ferrite changed to a-b plan direction. It was confirmed the BaFe12-2xCoxTixO19(x = 0.8 to 1.6) was synthesized by the sol-gel process and it was annealed at 900°C and 1200°C, which could be used as a wave absorber in the X-band region of 10 GHz less.
U-type ferrite typified by Ba4Co2Fe36O60 is used as a RAM (Radar Absorbing Materials) in the X-band (8-12 GHz). Ba4Co2Fe36O60 is known to have a complex crystal structure, which makes it difficult to obtain single phase and have low reproducibility. Previously known U-type ferrites have been fabricated based on a ceramic process that mixing (by a ball mill), calcining, grinding, binder mixing, drying, sieving, pressing and sintering. In contrast, the process of preparing the powder by the sol-gel method and its heat-treating is advantageous in that it can reduce the process steps and the required time. In addition, the precise stoichiometric control by the sol-gel method can effectively evaluate the effect of added or substituted elements. In this study investigates the crystal structure of Ba4Co2Fe36O60 synthesized by the sol-gel method and the morphology of U-type ferrite nano-powders according to various heat treatment conditions. Analysis of the crystal structure is used for XRD. Morphology and size are observed by SEM. In addition, VSM is performed to confirm the change of magnetic properties according to various heat treatment conditions.
In paper is presented technology of bimetallic layered castings based on founding method of layer coating directly in cast process so-called method of mould cavity preparation. Prepared castings consist two fundamental parts i.e. bearing part and working part (layer). The bearing part of bimetallic layered casting is typical foundry material i.e. unalloyed cast steel, whereas working part is plate of austenitic alloy steel sort X2CrNi 18-9. The ratio of thickness between bearing and working part is 8:1. The aim of paper was assessed the quality of the joint between bearing and working part in dependence of pouring temperature and carbon concentration in cast steel. The quality of the joint in bimetallic layered castings was evaluated on the basis of ultrasonic non-destructive testing, structure and microhardness researches.
In paper is presented technology of bimetallic layered castings based on founding method of layer coating directly in cast proces so-called method of mould cavity preparation. Prepared castings consist two fundamental parts i.e. bearing part and working part (layer). The bearing part of bimetallic layered casting is typical foundry material i.e. ferritic-pearlitic unalloyed cast steel, whereas working part (layer) is plate of austenitic alloy steel sort X2CrNi 18-9. The ratio of thickness between bearing and working part is 8:1. The aim of paper was assessed the quality of the joint between bearing and working part in dependence of pouring temperature and carbon concentration in cast steel. The quality of the joint in bimetallic layered castings was evaluated on the basis of ultrasonic non-destructive testing, structure and microhardness researches.
Image analysis allows to acquire a number of valuable quantitative informations on the observed structure and make appropriate conclusions. So far, a large part of analyzed images came only from light microscopes, where it was a possibility of accurately distinguish the different phases on the plane. However, the problem happened in the case of the observation of images obtained by scanning electron microscopy. In this case, the presence of various shades of gray, and the spaciousness of the image attained. To perform the analysis the matrix images of the ausferritic ductile iron were used. Full analysis was carried out using the computer program MicroMeter 1.03. Results obtained in the analysis were related directly to the results from X-ray diffraction. Obtained as a result of the analysis were related directly to the results from X-ray diffractometer. The following technique has weaknesses, including the misinterpretation by the operator microscope or program. After all, it was possible to obtain similar results to the result that has been obtained from X-ray diffractometer.
Determination of the ferrite content in austenitic steels, which solidified under defined conditions. Ferrite content in austenitic matrix was determined from samples with wall thickness of 60 mm. Measured ferrite contents served to propose the regression equations for the calculation of the ferrite content in steels with Cr content of 18 up to 22 % and Ni of 9 up to 11 %. An additional regression equation was proposed for steels with a higher Ni content. The proposed regression equations have been checked up on the operating melts. In conclusion, the ferrite content in the axis of the casting of wall thickness of 500 mm has been calculated and it was compared to the ferrite determined in the usual way from the cast-on test.
The article deals with the influence of chemical composition of martensitic stainless steel for castings GXCrNi13-4 (the 1.4317 material) on mechanical properties and structure of as cast steel after heat treatment. Properties of these martensitic stainless steel are heavily influenced by chemical composition and structure of the material after heat treatment. Structure of these steels after quenching is formed with martensite and residual austenite. When tempering the steel the carbon content in martensite is reduced and gently deposited carbides occur. The way of heat treatment has a major impact on structure of martensitic steels with low carbon content and thus on strength, hardness and elongation to fracture of these steels. Chemical composition of the melt has been treated to the desired composition of the lower, middle and upper bounds of the nickel content in the steel within the limits allowed by the standard. Test blocks were gradually cast from the melt. The influence of the nickel equivalent value on structure and properties of the 1.4317 steel was determined from results of mechanical tests.
The material selected for this investigation was low alloy steel weld metal deposit (WMD) after MAG welding with micro-jet cooling. The present investigation was aimed as the following tasks: analyze impact toughness of WMD in terms of micro-jet cooling parameters. Weld metal deposit (WMD) was first time carried out for MAG welding with micro-jet cooling of compressed air and gas mixture of argon and air. Until that moment only argon, helium and nitrogen and its gas mixture were tested for micro-jet cooling
A mathematical model of austenite - bainite transformation in austempered ductile cast iron has been presented. The model is based on a model developed by Bhadeshia [1, 2] for modelling the bainitic transformation in high-silicon steels with inhibited carbide precipitation. A computer program has been developed that calculates the incubation time, the transformation time at a preset temperature, the TTT diagram and carbon content in unreacted austenite as a function of temperature. Additionally, the program has been provided with a module calculating the free energy of austenite and ferrite as well as the maximum driving force of transformation. Model validation was based on the experimental research and literature data. Experimental studies included the determination of austenite grain size, plotting the TTT diagram and analysis of the effect of heat treatment parameters on the microstructure of ductile iron. The obtained results show a relatively good compatibility between the theoretical calculations and experimental studies. Using the developed program it was possible to examine the effect of austenite grain size on the rate of transformation.