Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 50
items per page: 25 50 75
Sort by:

Abstract

Introduction: Platelet-rich plasma (PRP) preparations can be used in bone tissue healing but there are numerous doubts among clinical orthopedists about effectiveness of this method. Materials and methods: The studies were carried out in 12 rabbits of white termond breed. In operating room we operationally generated cylindrical, unicortical defects of the diameter of 4 mm in the middle of the shafts of both femurs. The defects in the left bones were left without filling and served as controls, and 0.7 ml of the ready-to-use PRP was administered to the defects in the right bones (experimental group). We evaluated the usefulness of the diagnostic methods applied: biomechanical tests, micro-CT tests, densitometry, typical radiology, macroscopic measurements, histopathological examinations. Results: The macroscopic measurements showed a statistically significant increase in the dimension in the area of the right defect filled with PRP in relation to the control group. In experimented group, the assessment of the X-ray images showed the formation of a callus cuff around the defects. Densitometric examinations showed no statistically significant differences between defects in the experimental and control group. The analysis of the micro-CT examina- tions showed an increase in the total volume of the tissue examined (Vb) and the low density tissue fraction (Vb2) in the experimental group. The biomechanical examinations revealed signi- ficant decrease in the maximum breaking force (F max) necessary to break the bone in the experi- mental group in relation to the control group. Conclusions: Platelet-rich plasma (PRP) stimulates bone formation in the area of bone defects and may accelerate bone regeneration.
Go to article

Abstract

The aim of the study was to find out whether carriers of new lethal mutation in SDE2 gene occur in the population of Polish Holstein-Friesian bulls. Eighty seven bulls were included in the analysis. Bulls were selected as having in the pedigree known carrier of SDE2 mutation (bull Mountain USAM000002070579). All bulls were diagnosed by PCR amplification of 524 bp fragment of SDE2 gene followed by digestion of Bcc I restriction enzyme. Heterozygotes (carriers) were confirmed by sequencing. Each new carrier was used to trace another potential carriers among its offspring available in Polish Holstein Bull Repository Database. Among 87 bulls, 50 new SDE2 carriers were found. The study has shown that mutation in SDE2 gene causing early embryo mortality is already transmitted to Polish Holstein-Friesian cattle. The results are sufficient to initiate the screening program to reveal new carriers and to avoid further spreading of SDE2 lethal mutation.
Go to article

Abstract

The mathematical model and numerical simulations of the solidification of a cylindrical shaped casting, which take into account the process of filling the mould cavity by liquid metal and feeding the casting through the riser during its solidification, are presented in the paper. Mutual dependence of thermal and flow phenomena were taken into account because have an essential influence on solidification process. The effect of the riser shape on the effectiveness of feeding of the solidifying casting was determined. In order to obtain the casting without shrinkage defects, an appropriate selection of riser shape was made, which is important for foundry practice. Numerical calculations of the solidification process of system consisting of the casting and the conical or cylindrical riser were carried out. The velocity fields have been obtained from the solution of momentum equations and continuity equation, while temperature fields from solving the equation of heat conductivity containing the convection term. Changes in thermo-physical parameters as a function of temperature were considered. The finite element method (FEM) was used to solve the problem.
Go to article

Abstract

Micro-defects detection in solidified castings of aluminum alloy has always been a hot topic, and the method employed is mainly depends upon the size and shape of the specimens. In present paper, the amount and distribution characters of micro-defects in a series of 2219 aluminum alloy ingot, with diameters of φ1380 mm, φ1250 mm, φ1000 mm, φ850 mm and φ630 mm, prepared by direct chill casting were investigated by means of metallographic, respectively. Samples were cut along the radius direction from slices in the steady casting stage. The result reveals that typical micro-defects are consist of inclusions, porosity and shrinkage under optical microscope, and the total amount of micro-defect per unit area in an ingot slightly decreased with the increase of its diameter. Meanwhile, defects were classified into 2 types according to its size, the results suggesting that defects greater than 40 μm account for the largest proportion among the counted two kinds of defects. Moreover, the distribution of defects greater than 40 μm along the radial direction was detected, its amount increases as its distance from the side, indicating that the micro-defects greater than 40 μm distributed the most in the center zone of ingots and the larger the ingot diameter, the more obvious the tendency was.
Go to article

Abstract

Advanced vision method of analysis of the Erichsen cupping test based on laser speckle is presented in this work. This method proved to be useful for expanding the range of information on material formability for two commonly used grades of steel sheets: DC04 and DC01. The authors present a complex methodology and experimental procedure that allows not only to determine the standard Erichsen index but also to follow the material deformation stages immediately preceding the occurrence of the crack. Accurate determination of these characteristics in the sheet metal forming would be an important application, especially for automotive industry. However, the sheet metal forming is a very complex manufacturing process and its success depends on many factors. Therefore, attention is focused in this study on better understanding of the Erichsen index in combination with the material deformation history.
Go to article

Abstract

This study summarises the research efforts undertaken in iron foundry plants in which the process are mostly automated and mechanised. The research program was limited in scope, focusing on causes of surface defects in castings products that are attributable to the bentonite-containing sand and the mould system. One of the potential roots of surface defects is heterogeneity of sand grains, containing lumped ball-shaped grains and irregular pellets with a layered-structure. The moisture contents of those lumped grains is different than the moisture level required in the process, besides these grains may contain various elements and metallic compounds which, when cast into moulds, may react with molten metals in an uncontrolled manner. As a result, surface defects are produced, such as surface blowholes, burst penetration, sand holes, slag inclusions, pinhole porosity. This study investigated the efficiency of key sand preparation and moulding machines and installations integrated into the casting process line. The efficiency of machines and installations is defined in terms of quality parameters of sand mix and moulds, which are associated with the emergence of surface defects on castings.
Go to article

Abstract

Definition of a composite [1] describes an ideal composite material with perfect structure. In real composite materials, structure is usually imperfect – composites contain various types of defects [2, 3–5], especially as the casted composites are of concern. The reason for this is a specific structure of castings, related to course of the manufacturing process. In case of metal matrix composite castings, especially regarding these manufactured by saturation, there is no classification of these defects [2, 4]. Classification of defects in castings of classic materials (cast iron, cast steel, non-ferrous alloys) is insufficient and requires completion of specific defects of mentioned materials. This problem (noted during manufacturing metal matrix composite castings with saturated reinforcement in Institute of Basic Technical Sciences of Maritime University Szczecin) has become a reason of starting work aimed at creating such classification. As a result, this paper was prepared. It can contribute to improvement of quality of studied materials and, as a consequence, improve the environment protection level.
Go to article

Abstract

The purpose of the study was to assess the effect of autologous activated platelet-rich plasma on healing of a bone substitute - tricalcium phosphate hydroxyapatite in experimental long bone defects using an animal model. The experiment involved an animal model of femoral defect. 24 Termond white rabbits were used in the study. We evaluated the effect of autologous platelet-rich plasma on tricalcium phos- phate using classical radiology, micro-CT studies, strength tests and histological evaluation. Radiological and histological assessment did not show a beneficial effect of PRP together with a bone substitute in comparison to filling the defects only with bone replacement material. The only benefit of adding platelet-rich plasma to a bone substitute was shown in microCT imaging. Autologous, activated platelet-rich plasma combined with hydroxyapatite tricalcium phos- phate has a positive effect on the remodeling of the newly formed bone tissue, increasing its density.
Go to article

Abstract

The paper includes validation studies of the flow module of the NovaFlow&Solid simulation code. Experiments of ductile iron and gray iron casting in a spiral test of castability were carried out. Casting experiments were then carried out in industrial conditions in the Ferrex Foundry in Poznań and the results are the castability spiral length and local cast iron rate during mould cavity pouring. Simulation tests using NovaFlow&Solid Control Volume code were made. The technological castability test was used to determine thermal-physical data through simplified inversion problem. Influence of physical parameters in the database of simulation code on the spiral length obtained as the result of simulation was analyzed. It was found that critical fraction of capillary flow CLFdown has the biggest impact on cast iron castability in the simulation code. The simulations resulted in defining parameters of gray iron GJL 250 and ductile iron GJS-400-15. For the parameters set, the length of castability spiral in simulations was in accordance with casting experiments.
Go to article

Abstract

The article presents an analysis of the multi-operation hot die forging process, performed on a press, of producing a lever forging used in the motorcycles of a renowned producer by means of numerical simulations. The investigations were carried out in order to improve (perfect) the currently applied production technology, mainly due to the presence of forging defects during the industrial production process. The defects result mainly from the complicated shape of the forging (bent main axis, deep and thin protrusions, high surface diversity in the cross section along the length of the detail), which, during the filling of the die by the deformed material, causes the presence of laps, wraps and underfills on the forging. Through the determination of the key parameters/quantities during the forging process, which are difficult to establish directly during the industrial process or experimentally, a detailed and complex analysis was performed with the use of FEM as well as through microstructure examinations. The results of the performed numerical modelling made it possible to determine: the manner of the material flow and the correctness of the impression filling, as well as the distributions of temperature fields and plastic deformations in the forging, and also to detect the forging defects often observed in the industrial process. On this basis, changes into the process were introduced, making it possible to improve the currently realized technology and obtain forgings of the proper quality as well as shape and dimensions.
Go to article

Abstract

Diagnostics of composite castings, due to their complex structure, requires that their characteristics are tested by an appropriate description method. Any deviation from the specific characteristic will be regarded as a material defect. The detection of defects in composite castings sometimes is not sufficient and the defects have to be identified. This study classifies defects found in the structures of saturated metallic composite castings and indicates those stages of the process where such defects are likely to be formed. Not only does the author determine the causes of structural defects, describe methods of their detection and identification, but also proposes a schematic procedure to be followed during detection and identification of structural defects of castings made from saturated reinforcement metallic composites. Alloys examination was conducted after technological process, while using destructive (macroscopic tests, light and scanning electron microscopy) and non-destructive (ultrasonic and X-ray defectoscopy, tomography, gravimetric method) methods. Research presented in this article are part of author’s work on castings quality.
Go to article

Abstract

The powerful tool for defect analysis is an expert system. It is a computer programme based on the knowledge of experts for solving the quality of castings. We present the expert system developed in the VSB-Technical University of Ostrava called ‘ESWOD’. The ESWOD programme consists of three separate modules: identification, diagnosis / causes and prevention / remedy. The identification of casting defects in the actual form of the system is based on their visual aspect.
Go to article

Abstract

The paper deals with fault diagnosis of nonlinear analogue integrated circuits. Soft spot short defects are analysed taking into account variations of the circuit parameters due to physical imperfections as well as self-heating of the chip. A method enabling to detect, locate and estimate the value of a spot defect has been developed. For this purpose an appropriate objective function was minimized using an optimization procedure based on the Fibonacci method. The proposed approach exploits DC measurements in the test phase, performed at a limited number of accessible points. For illustration three numerical examples are given.
Go to article

Abstract

This paper concerns the issues of measurement techniques, analysis and assessment of the machined surface geometric structure. The aim of this work was to show the application of surface analysis in diagnosing the causes of discrepancies occurring in the manufacturing process, which may result from ill-matched (poorly fitting) process parameters. An appropriate system of control and interpretation of results may allow early reaction to unfavorable trends (for example blunting of the tool) and prevention of undesirable defects. The subject of research was a waste basket used in the construction of retaining sewer systems. In this paper, the quality of the waste basket as well as its manufacturing process were analyzed and assessed. The research was carried out with the use of three measurement stands, i.e. optical microscopy (OM), scanning electron microscopy (SEM) and white light interferometer (WLI). The surface analysis proved to be important from the viewpoint of outlining the production process as well as improving the product quality. The software used for topographical analysis appeared to be significant for the success of the analysis, providing notable economic effects, namely the lack of defects.
Go to article

Abstract

This paper presents a geomagnetic detection method for pipeline defects using complete ensemble empirical mode decomposition with adaptive noise (CEEMDAN) and wavelet energy product (WEP) – Teager energy operator (TEO), which improves detection accuracy and defect identification ability as encountering strong inference noise. The measured signal is first subtly decomposed via CEEMDAN into a series of intrinsic mode functions (IMFs), which are then distinguished by the Hurst exponent to reconstruct the filtered signal. Subsequently, the scale signals are obtained by using gradient calculation and discrete wavelet transform and are then fused by using WEP. Finally, TEO is implemented to enhance defect signal amplitude, completing geomagnetic detection of pipeline defects. The simulation results created by magnetic dipole in a noisy environment, indoor experiment results and field testing results certify that the proposed method outperforms ensemble empirical mode decomposition (EEMD)-gradient, EEMD-WEP-TEO, CEEMDAN-gradient in terms of detection deviation, peak side-lobe ratio (PSLR) and integrated side-lobe ratio (ISLR).
Go to article

Abstract

A significant part of the knowledge used in the production processes is represented with natural language. Yet, the use of that knowledge in computer-assisted decision-making requires the application of appropriate formal and development tools. An interesting possibility is created by the use of an ontology that is understandable both for humans and for the computer. This paper presents a proposal for structuring the information about the foundry processes, based on the definition of ontology adapted to the physical structure of the ongoing technological operations that make up the process of producing castings.
Go to article

Abstract

Magnesium alloys due to their low density and high strength-to-weight ratio are promising material for the automotive and aerospace industries. Many elements made from magnesium alloys are produced by means of sand casting. It is essential to investigate impact of the applied mould components on the microstructure and the quality of the castings. For the research, six identical, 100x50x20mm plates has been sand cast from the Elektron 21 magnesium casting alloy. Each casting was fed and cooled in a different way: one, surrounded by mould sand, two with cast iron chills 20mm and 40mm thick applied, another two with the same chills as well as feeders applied and one with only the feeder applied. Solid solution grain size and eutectics volume fraction were evaluated quantitatively in Met-Ilo program, casting defects were observed on the scanning electron microscope Hitachi S3400N. The finest solid solution grain was observed in the castings with only the chills applied. Non metallic inclusions were observed in each plate. The smallest shrinkage porosity was observed in the castings with the feeders applied.
Go to article

Abstract

Simulation software dedicated for design of casting processes is usually tested and calibrated by comparisons of shrinkage defects distribution predicted by the modelling with that observed in real castings produced in a given foundry. However, a large amount of expertise obtained from different foundries, including especially made experiments, is available from literature, in the form of recommendations for design of the rigging systems. This kind of information can be also used for assessment of the simulation predictions. In the present work two parameters used in the design of feeding systems are considered: feeding ranges in horizontal and vertical plates as well as efficiency (yield) of feeders of various shapes. The simulation tests were conducted using especially designed steel and aluminium castings with risers and a commercial FDM based software. It was found that the simulations cannot predict appearance of shrinkage porosity in horizontal and vertical plates of even cross-sections which would mean, that the feeding ranges are practically unlimited. The yield of all types of feeders obtained from the simulations appeared to be much higher than that reported in the literature. It can be concluded that the feeding flow modelling included in the tested software does not reflect phenomena responsible for the feeding processes in real castings properly. Further tests, with different types of software and more fundamental studies on the feeding process modelling would be desirable.
Go to article

Abstract

Changes of gas pressure in the moulding sand in the zone adjacent to mould cavity were analysed during pouring of cast iron. No significant effect of pressure on the surface quality of castings was observed. In the second series of tests, the concentration of hydrogen in the gas atmosphere was measured. It has been found that the value of this concentration depends on metal composition and is particularly high in cast iron containing magnesium. This is due to the reduction of water vapour with the element that has high affinity to oxygen. The presence of hydrogen causes the formation of gas-induced defects on the casting surface.
Go to article

Abstract

Gas atmosphere at the sand mould/cast alloy interface determines the quality of the casting obtained. Therefore the aim of this study was to measure and evaluate the gas forming tendency of selected moulding sands with alkyd resins. During direct and indirect gas measurements, the kinetics of gas evolution was recorded as a function of the temperature of the sand mixture undergoing the process of thermal destruction. The content of hydrogen and oxygen was continuously monitored to establish the type of the atmosphere created by the evolved gases (oxidizing/reducing). The existing research methodology [1, 7, 8] has been extended to include pressure-assisted technique of indirect measurement of the gas evolution rate. For this part of the studies, a new concept of the measurement was designed and tested. This article presents the results of measurements and compares gas emissions from two sand mixtures containing alkyd resins known under the trade name SL and SL2002, in which the polymerization process is initiated with isocyanate. Studies of the gas forming tendency were carried out by three methods on three test stands to record the gas evolution kinetics and evaluate the risk of gas formation in a moulding or core sand. Proprietary methods for indirect evaluation of the gas forming tendency have demonstrated a number of beneficial aspects, mainly due to the ability to record the quantity and composition of the evolved gases in real time and under stable and reproducible measurement conditions. Direct measurement of gas evolution rate from the tested sands during cast iron pouring process enables a comparison of the results with the results obtained by indirect methods.
Go to article

Abstract

Simulation software can be used not only for checking the correctness of a particular design but also for finding rules which could be used in majority of future designs. In the present work the recommendations for optimal distance between a side feeder and a casting wall were formulated. The shrinkage problems with application of side feeders may arise from overheating of the moulding sand layer between casting wall and the feeder in case the neck is too short as well as formation of a hot spot at the junction of the neck and the casting. A large number of simulations using commercial software were carried out, in which the main independent variables were: the feeder’s neck length, type and geometry of the feeder, as well as geometry and material of the casting. It was found that the shrinkage defects do not appear for tubular castings, whereas for flat walled castings the neck length and the feeders’ geometry are important parameters to be set properly in order to avoid the shrinkage defects. The rules for optimal lengths were found using the Rough Sets Theory approach, separately for traditional and exothermic feeders.
Go to article

Abstract

The chosen, typical causes of quality defects of cast-iron „alphin” rings embedded in aluminum cast are being presented in this paper. Diffusive joint of those inserts with the pistons casts is being used, due to extreme work conditions of destructive influence of the fuel mix and variable thermo-mechanical loads, which reign in the combustion motor working chamber.
Go to article

Abstract

The article summarizes the theoretical knowledge from the field of brazing of graphitic cast iron, especially by means of conventional flame brazing using a filler metal based on CuZn (CuZn40SnSi – brass alloy). The experimental part of the thesis presents the results of performance assessment of brazed joints on other than CuZn basis using silicone (CuSi3Mn1) or aluminium bronze (CuAl10Fe). TIG electrical arc was used as a source of heat to melt these filler materials. The results show satisfactory brazed joints with a CuAl10Fe filler metal, while pre-heating is not necessary, which favours this method greatly while repairing sizeable castings. The technological procedure recommends the use of AC current with an increased frequency and a modified balance between positive and negative electric arc polarity to focus the heat on a filler metal without melting the base material. The suitability of the joint is evaluated on the basis of visual inspection, mechanic and metallographic testing.
Go to article

Abstract

The paper presents the results of experimental-simulation tests of expansion-shrinkage phenomena occurring in cast iron castings. The tests were based on the standard test for inspecting the tendency of steel-carbon alloys to create compacted discontinuities of the pipe shrinkage type. The cast alloy was a high-silicone ductile iron of GJS - 600 - 10 grade. The validation regarding correctness of prognoses of the shrinkage defects was applied mostly to the simulation code (system) NovaFlow & Solid CV (NFS CV). The obtained results were referred to the results obtained using the Procast system (macro- and micromodel). The analysis of sensitivity of the modules responsible for predicting the shrinkage discontinuities on selected pre-processing parameters was performed, focusing mostly on critical fractions concerning the feeding flows (mass and capillary) and variation of initial temperature of the alloy in the mould and heat transfer coefficient (HTC) on the casting - chill interface.
Go to article

This page uses 'cookies'. Learn more