The author analyses onymic practices of Poznań–based craftsmen forming guilds. In the names of the inhabitants of Poznań, which stabilised until the end of the 18th century, she seeks traces of the so-called cognomens, i.e. secondary personal designations granted to apprentices who were becoming masters. The names resulted from community acts of creation, which were of ludic nature. Referring to German onymic practices and pointing to the so-called Schleifnamen, the author discusses specific codes of European middle-class culture. She focuses on the transfer of models and patterns to Polish urban communities.
There is a considerable increase in the use of noise barriers in recent years. Noise barriers as a control noise solution can increase the insertion loss to protect receivers. This paper presents the results of an investigation about the acoustic efficiency of primitive root sequence diffuser (PRD) on an environmental single T-shape barrier design. A 2D boundary element method (BEM) is used to predict the insertion loss of the tested barriers. The results of rigid and with a different sequence diffuser coverage are also predicted for comparison. Employing PRD on the top surface of T-shape barrier has been found to improve the performance of barriers in comparison with the use of rigid and QRD coverage at the examined receiver locations. It has been found that decreasing the design frequency of PRD shifts the frequency effects towards lower frequencies, and therefore the overall A-weighted insertion loss is improved. It was also found that using wire mesh with reasonably efficient resistivity on the top surface of PRD improves the efficiency of the reactive barriers; however utilizing wire meshes with flow resistivity higher than the specific acoustic impedance of air on the PRD top of a diffuser barrier significantly reduces the performance of the barrier within the frequency bandwidth of the diffuser. The performance of a PRD covered T-shape barrier at 200 Hz was found to be higher than that of its equivalent QRD barriers in both the far field and in areas close to the ground. The amount of improvement compared made by PRD barrier compared with its equivalent rigid barrier at far field is about 2 to 3 dB, while this improvement relative to the barrier model "QR4" can reach up to 4-6 dB.
The paper deals with the problem of acoustic correction in historic opera theatres with the auditorium layout in the form of a horseshoe with deep underbalcony cavities limited with a semicircular wall surface. Both geometry of the cavities and excessive sound absorption determine acoustic phenomena registered in this area of the hall. The problem has been observed in the Theatre of Opera and Ballet in Lviv, Ukraine, where acoustic tests were carried out, simulation calculations performed, and finally a diffusion panel worked out designed for the rear wall of the underbalcony space. Acoustic measurements carried out after installation of the diffusers revealed favourable changes in the sound strength factor G within the range of medium and high frequencies in the underbalcony and auditorium centre area. By replacing textile tapestry with diffusion panels, a significant reduction of sound absorption was achieved for the frequency range above 1 kHz and an increase of uniformity of acoustic parameters registered in the hall. The method presented in the paper can be applied in historic halls of the similar type as well as contemporary rooms where there is a need for correction of acoustic flaws related to sound focusing or the echo effect.
The presence of more than one solute diffused in fluid mixtures is very often requested for discussing the natural phenomena such as transportation of contaminants, underground water, acid rain and so on. In the paper, the effect of nonlinear thermal radiation on triple diffusive convective boundary layer flow of Casson nanofluid along a horizontal plate is theoretically investigated. Similarity transformations are utilized to reduce the governing partial differential equations into a set of nonlinear ordinary differential equations. The reduced equations are numerically solved using Runge-Kutta-Fehlberg fourth-fifth order method along with shooting technique. The impact of several existing physical parameters on velocity, temperature, solutal and nanofluid concentration profiles are analyzed through graphs and tables in detail. It is found that, modified Dufour parameter and Dufour solutal Lewis number enhances the temperature and solutal concentration profiles respectively.
By means of small wind turbines, it is possible to create distributed sources of electricity useful in areas with good wind conditions. Sometimes, however, it is possible to use small wind turbines also in areas characterized by lower average wind speeds during the year. At the small wind turbine design stage, various types of technical solutions to increase the speed of the wind stream, as well as to optimally orientate it, can be applied. The methods for increasing the efficiency of wind energy conversion into electricity in the case of a wind turbine include: the use of a diffuser shielding the turbine rotor and the optimization of blades mounted on the turbine rotor. In the paper, the influence of the diffuser and rotor blades geometry on the efficiency of an exemplary wind turbine for exploitation in the West Pomeranian Province is investigated. The analyses are performed for three types of the diffuser and for three types of rotor blades. Based on them, the most optimal shapes of the diffuser and blades are selected due to the efficiency of the wind turbine. For the turbine with the designed diffuser, calculations of the output power for the assumed different values of the average annual wind speed and the constant Betz power factor and the specified generator efficiency are made. In all the analyzed cases, the amount of energy that can be generated by the turbine during the year is also estimated. Important practical conclusions are formulated on the basis of these calculations. In the final part of the paper, a 3D model of the wind turbine with the diffuser and rotor blades chosen based on earlier analyses is presented. As a material for the diffuser and rotor blades, glass fiber type A is applied. By means of calculations using the finite element method, the limit displacement of the turbine structure under the influence of a hurricane wind are determined. Based on these calculations, the correctness of the modelled small wind turbine structure has been demonstrated.
This paper presents an approximate analytical model for estimating the transmission loss (TL) of a finite rectangular plate in the low frequency range, which is based on the modal summation approach (MSA) taking into account the modal radiation impedance and fluid loading. The mode-dependent radiation resistance is calculated using the Rayleigh integral. The fluid loading is taken into account through the natural frequency modified by the added mass. The results are compared with the ones of Statistical Energy Analysis (SEA) coupled with FEM and FEM coupled with BEM. In addition, the effects of the various vibration modes and the fluid loading on TL, and a way for reducing the calculation time are discussed.