A novel laser diode based length measuring interferometer for scientific and industrial metrology is presented. Wavelength the stabilization system applied in the interferometer is based on the optical wedge interferometer. Main components of the interferometer such as: laser diode stabilization assembly, photodetection system, measuring software, air parameters compensator and base optical assemblies are described. Metrological properties of the device such as resolution, measuring range, repeatability and accuracy are characterized.
Knowledge of gravitational acceleration in metrology is required for traceable force and pressure calibrations, furthermore the redefinition of the SI base unit of kilogram requires absolute accomplishment of the gravitational acceleration. A direct free-fall gravimeter is developed using pneumatic grippers for test mass handling and a semi-rotary actuator for repositioning, i.e. automated re-launching. The catch and release system is powered by compressed air. This eliminates electric interferences around the test mass. A simplified method of signal capturing and processing is used on the designed gravimeter. A digital frequency trigger is implemented in the post processing algorithms to ensure that the signals are analysed from the identical effective height. The experimental results measured the site gravitational acceleration of 9.786043 ms��2 with a statistical uncertainty of #6;29 ms��2.
The paper presents the properties of a strain sensor, which was made using the micro hole collapse method and operates in the configuration of a Mach-Zehnder modal interferometer with a PM-1550-01 polarization maintaining photonic crystal fibre. The sensor’s transfer curve was determined analytically. Its strain sensitivity, determined from measurements, decreases slightly with increasing wavelength and is in a range from 2:01 to 2:23 pm/me in the wavelength range 1520–1580 nm. Based on the Fourier analysis of the wavelength spectrum of the constructed sensor, the difference of the group refractive indices of the core and the cladding of the photonic crystal fibre was determined, which are in a range from 7:45#1;103 to 1:01#1;102. The temperature sensitivity of the sensor, determined on the basis of measurements performed in a range from 23 to 60◦C, is positive and equals 5.9 pm/K.
This paper presents two methods for evaluation of the effective wavenumber of nearly-Gaussian beams in laser interferometers that can be used for determination of a so called diffraction correction in absolute gravimeters. The first method, that can be simply used in situ, is an empirical procedure based on the evaluation of the variability of g measurements against the amount of light limited by an iris diaphragm and transmitted to a photodetector. However, precision of this method depends on the beam quality similarly as in the case of the conventional method based on measurement of a beam width. The second method, that is more complex, is based on beam profiling in various distances and on calculation of the effective wavenumber using the second spatial derivative of a non-ideal beam field envelope. The measurement results achieved by both methods are presented on an example of two absolute gravimeters and the determined diffraction corrections are compared with the results obtained by measurements of beam width. Agreement of methods within about 1 mGal have been obtained with average diffraction corrections slightly exceeding +2 mGal for three FG5(X) gravimeter configurations.
The results of surface texture measurements obtained with the stylus equipment, white light interferometer and confocal profilometer of the same samples were compared. Machined isotropic and anisotropic surfaces, of symmetric and asymmetric ordinate distribution were measured. Forms were removed using polynomials. Sampling intervals and measuring areas during computations of parameters were the same. Discrepancies between the results obtained with various methods were observed and discussed. It was found that errors of surface texture measurement with the optical methods depend on the type of surface topography.
In order to calibrate the stripe precision of a leveling rod, an automatic laser interferometer and a vision measurement system were designed by Xi’an University of Technology in China. The rod was driven by a closed-loop control and the data were collected at the stop state to ensure precision. The laser interferometer provided not only the long distance data but also a position feedback signal in the automatic control loop. CCD camera and a vision measurement method were used to inspect the stripe edge position and defect. A pixel-equivalent self-calibration method was designed to improve precision. ROI (regions of interest) method and an outline tracing method were designed to quickly extract multiple stripe edges. A combination of the image data with the interferometer data reduces control difficulty and ensures the measurement accuracy. The vision measurement method reached sub-pixel precision and the defective edges were reported. The system can automatically calibrate a stripe leveling rod with a high degree of efficiency and precision.
This work is focused on the issue of non-measured points – one of the most important problems in surface texture measurements using optical methods. The fundamental aim of this research is to analyse errors of surface texture measurements caused by the presence of non-measured points. This study is divided into two parts. In the first part, circles with non-measured points were artificially created on peak portions of measured surfaces. In the second part – the results of measurement by a Talysurf CCI Lite interferometer were analysed. A measurement area of 3.3 × 3.3 mm contained 1024 × 1024 points. The measurements were performed with different intensity of light. Changes of parameters regarding the analysed errors depended on a surface type. The following parameters are susceptible to errors: skewness Ssk, areal material ratio Smr, as well as the following feature parameters: Spd, Sda, Sdv, Sha and Shv. Inaccuracies of measurement in valley parts of two-process textures led usually to larger errors of parameter computations compared with deviations in peak portions.
A method for evaluating the dynamic characteristics of force transducers against small and short-duration impact forces is developed. In this method, a small mass collides with a force transducer and the impact force is measured with high accuracy as the inertial force of the mass. A pneumatic linear bearing is used to achieve linear motion with sufficiently small friction acting on the mass, which is the moving part of the bearing. Small and short-duration impact forces with a maximum impact force of approximately 5 N and minimum half-value width of approximately 1 ms are applied to a force transducer and the impulse responses are evaluated.
In recent years organic semiconductors have been given attention in the field of active materials for gas sensor applications. In the paper the investigations of the optoelectronic sensor structure of ammonia were presented. The sensor head consists of polyaniline and Nafion layers deposited on the face of the telecommunication optical fiber. The elaborated sensor structure in the form of Fabry-Perot interferometer is of the extremely small dimension its thickness is of the order of 1 um. Many sensor structures of diffierent combinations of the polyaniline and Nafion layers were constructed and investigated. The optimal solution seems to be the structures with small number of polianiline layers (up to three).