Search results

Filters

  • Journals
  • Date

Search results

Number of results: 5
items per page: 25 50 75
Sort by:

Abstract

This study offers a new method to synthesize facilely willemite (Zn2SiO4) based phosphor at the temperature of 800 °C. The ZnO-SiO2 nanocomposite was calcined at different temperatures between 500 and 1000 °C. The structural, morphological and optical properties of the nanocomposite obtained at various calcination temperatures were studied using different techniques. The FT-IR, XRD and the UV-vis result confirmed the formation of willemite phase. The precursor was confirmed to be amorphous by XRD at room temperature, but upon calcination temperature at 500 °C, it was transformed into a crystalline structure. The crystallinity and the particle size of the nanocomposite increase as the calcination temperature were increased as revealed by XRD and TEM measurement. The sample exhibits a spherical morphology from 500 to 800 °C and dumbbell-like morphology above 800 °C as shown by the FESEM images. The absorption spectrum suffers intense in lower temperature and tends to shift to lower wavelength in the UV region as the calcination temperature increases. The band gap values were found to be increasing from 3.228-5.550 eV obtained between 500 to 1000 °C, and all the results confirm the formation of willemite phase at 800 °C.
Go to article

Abstract

In this study, high performance magnesium-yttria nanocomposite’s room temperature, strength and ductility were significantly enhanced by the dispersion of nano-sized nickel particles using powder blending and a microwave sintering process. The strengthening effect of the dispersed nano-sized nickel particles was consistent up to 100°C and then it gradually diminished with further increases in the test temperature. The ductility of the magnesium-yttria nanocomposite remained unaffected by the dispersed nano-sized nickel particles up to 100°C. Impressively, it was enhanced at 150°C and above, leading to the possibility of the near net shape fabrication of the nanocomposite at a significantly low temperature.
Go to article

Abstract

Al-CuO is a thermite material exhibiting the exothermic reaction only when aluminum melts. For wide spread of its application, the reaction temperature needs to be reduced in addition to the enhancement of total reaction energy. In the present study, a thermite nanocomposite with a large contact area between Al and CuO was fabricated in order to lower the exothermic reaction temperature and to improve the reactivity. A cryomilling process was performed to achieve the nanostructure, and the effect of composition on the microstructure and its reactivity was studied in detail. The microstructure was characterized using SEM and XRD, and the thermal property was analyzed using DSC. The results show that as the molar ratio between Al and CuO varies, the fraction of uniform nanocomposite structure was changed affecting the exothermic reaction characteristics.
Go to article

Abstract

Fe-40wt% TiB2 nanocomposites were fabricated by mechanical activation and spark-plasma sintering of a powder mixture of iron boride (FeB) and titanium hydride (TiH2). The powder mixture of (FeB, TiH2) was prepared by high-energy ball milling in a planetary ball mill at 700 rpm for 3 h followed by spark-plasma sintering (SPS) at various conditions. Analysis of the change in relative sintered density and densification rate during sintering showed that a self-propagating high-temperature synthesis reaction occurs to form TiB2 from FeB and Ti. A sintered body with relative density higher than 98% was obtained after sintering at 1150°C for 5 and 15 min. The microstructural observation of sintered compacts with the use of FE-SEM and TEM revealed that ultrafine particulates with approximately 5 nm were evenly distributed in an Fe-matrix. A hardness value of 83 HRC was obtained, which is equivalent to that of conventional WC-20 Co systems.
Go to article

This page uses 'cookies'. Learn more