In 2015 an important part of the official evaluation of Polish scientific journals was left to experts’ judgement. In this paper we try to establish which observable factors (with available data) are closely related to the outcome of experts’ evaluation of Polish journals in economic sciences. Using the multiple regression statistical model we show that only 5 variables (out of 17) significantly explain almost 50% of the empirical variance of the experts’ evaluation. The determinants of particular interest, not entering the formal criteria and not related to the impact on global science, are: the number of citations mainly in Polish journals and the affiliation with the Polish Academy of Sciences.
Given a linear discrete system with initial state x0 and output function yi , we investigate a low dimensional linear systemthat produces, with a tolerance index ǫ, the same output function when the initial state belongs to a specified set, called ǫ-admissible set, that we characterize by a finite number of inequalities. We also give an algorithm which allows us to determine an ǫ-admissible set.
Heating of steel or structural aluminum alloys at a speed of 2 to 50 K/min – characterizing the fire conditions – leads to a reduction in mechanical properties of the analyzed alloys. The limit of proportionality fp, real fy and proof f₀₂ yield limit, breaking strength fu and longitudinal limit of elasticity E decrease as the temperature increases. Quantitative evaluation of the thermal conversion in strengths of structural alloys is published in Eurocodes 3 and 9, in the form of dimensionless graphs depicting reduction coefficients and selected (tabulated) discrete values of mechanical properties. The author’s proposal for an analytical formulation of code curves describing thermal reduction of elasticity modulus and strengths of structural alloys recommended for an application in building structures is presented in this paper.
It is contended that, in essence, climate policy is sustainable development policy, given that it postulates the use of renewable resources, and an increase in the effectiveness of use of non-renewable ones. Furthermore, it serves the security of future generations more than present ones; for while unfavourable impacts of climate change are already making their presence felt, truly negative consequences of considerable signifi cance are likely to be more of a matter for the second half of the present century. This is why, in analysing the evolution of the approach to climate policy through the late 20th century and into the 21st, it is also possible to appraise changes in the approach to the sustainable-development concept. This article has therefore sought to offer the author’s analysis of how the approach to sustainable development has evolved, by reference to Poland’s climate policy from 1988 through to 2016. As this is done, an attempt is also made to identify the conditioning that has decided upon and will go on determining the shape of national policy in this domain. Climate policy in Poland has been developing since the early 1990s. At the outset, it was not a source of controversy, with the consequence that the country rather rapidly signed up to and then ratifi ed the Kyoto Protocol to the UN Framework Convention on Climate Change. However, as early as in the late 1990s, reservations began to be expressed, to the effect that actions to protect the climate might pose a threat to Poland’s economy. A key turning point as regards the approach came with the growing dispute over the EU 2020 Climate and Energy Package. It was also at this time that a thesis began to take shape, holding that the goals of climate policy where at best unfavourable and at worst dangerous for Poland. This approach in fact held sway in successive years, leaving this country’s cooperation with the EU over this matter severely hindered. The main reason for this change of approach to climate policy can be considered to lie in the politicisation thereof, and hence the increasing dominance of the short-term interests of the Polish political elite over either the public interest or the security of future generations.
The increment in the number of automobiles and the densification of the city has increased noise pollution rates. In addition, the lack of regulation in Chile regarding the acoustic insulation of façades is a problem of a growing concern. The main objective of the present study was to obtain a model of the Sound Insulation of housing, façades, stratified in Santiago, Chile, based on constructive variables. It is expected to serve as a basis for one future regulation for acoustic façades of houses. In the present study, tests based on the international ISO 140-5 standard were carried out in situ. An estimation model of the Standardized Level Difference Dls,2m,nT,w + C, was obtained based on the opening/façade proportion, and the type of glass used for the windows.
Application of active noise reduction (ANR) systems in hearing protectors requires the use of control algorithms to ensure stability of the ANR system and at the same time highly effective active noise reduction. A control algorithm based on NOTCH filters is an example of solutions that meet these criteria. Their disadvantage is operation over a narrow frequency band and a need for prior determination of frequencies to be reduced. This paper presents a solution of the ANR system for hearing protectors which is controlled with the use of modified NOTCH filters with parameters determined by a genetic algorithm. Application of a genetic algorithm allows to change the NOTCH filter reference signal frequency, and thus, adapt the filter to the reduced signal frequency.
In 2011, over 520 thousand persons worked in hazardous conditions (according to the GUS). Among hazardous factors related to working environment noise was found to be the most common one, threatening 199,6 thousand people (52.9% threats-per-persons related to working environment). The prevalence of workplace noise and increasing awareness of effects of its impact on the human body causes increase of the demand for knowledge of the methods of noise reduction. Due to the lack of knowledge concerning the proper use of hearing protectors, effective noise exposure in the real world may be about a dozen dB higher than the declared assumed protection value. For this reason, in Central Institute for Labour Protection - NRI “The interactive system for learning the correct use of hearing protectors” has been developed. The system includes a multimedia guide on hearing protectors supplemented by video tutorials, training materials with training hearing protectors, and software for evaluation of the activities of the trainee.
This article contains information concerning of the analysis the possibility of defining refinery qualities of the slag based thermo-physical and thermo-dynamical data. It was showed the brass refining with the many-carbide reagents introduced in to the slag. The paper presents the results of the structure analysis of the brass after carbide slag refining in the industrial conditions. The results of the macrostructure analysis have confirmed the argument on high reducing effectiveness of manganese and aluminium carbide used during CuZn39Pb2 alloy melting. The X-Ray microanalysis of the ingot cross-section has shown considerable discrepancies in the disposition of the inclusions. This effects showed on the great influence of reduction melting condition in to the brass melting
Pyrite framboids occur in loose blocks of plant−bearing clastic rocks related to volcano−sedimentary succession of the Mount Wawel Formation (Eocene) in the Dragon and Wanda glaciers area at Admiralty Bay, King George Island, West Antarctica. They were investigated by means of optical and scanning electron microscopy, energy−dispersive spectroscopy, X−ray diffraction, and isotopic analysis of pyritic sulphur. The results suggest that the pyrite formed as a result of production of hydrogen sulphide by sulphate reducing bacteria in near surface sedimentary environments. Strongly negative #2;34SVCDT values of pyrite (−30 – −25 ‰) support its bacterial origin. Perfect shapes of framboids resulted from their growth in the open pore space of clastic sediments. The abundance of framboids at cer− tain sedimentary levels and the lack or negligible content of euhedral pyrite suggest pulses of high supersaturation with respect to iron monosulphides. The dominance of framboids of small sizes (8–16 μm) and their homogeneous distribution at these levels point to recurrent development of a laterally continuous anoxic sulphidic zone below the sediment surface. Sedimentary environments of the Mount Wawel Formation developed on islands of the young magmatic arc in the northern Antarctic Peninsula region. They embraced stagnant and flowing water masses and swamps located in valleys, depressions, and coastal areas that were covered by dense vegetation. Extensive deposition and diagenesis of plant detritus in these environments promoted anoxic conditions in the sediments, and a supply of marine and/or volcanogenic sulphate enabled its bacterial reduction, precipitation of iron mono− sulphides, and their transformation to pyrite framboids.
Measurements were made of sediment characteristics, benthic microbial activity and optimum temperature for sulfate reduction at Signy Island, South Orkney Islands, Antarctica . There was little evidence to support any seasonal variation in oxygen penetration of surface sediments. Oxygen penetrated to only 1.5 to 3 mm throughout the year, despite bioturbation from a dense amphipod population. The distribution of acid volatile sulfides increased with depth below 1 cm and above this, surface sediments were lighter in colour and contained fewer sulfides. The rates of sulfate reduction increased during winter under sea-ice cover, and remained high after ice break up. Seasonal water temperature was relatively constant between –1.8 and 0.5°C. Optimum temperature for anaerobic sediment respiration was investigated using different substrates and was found to be in the range 17–27°C, suggesting that sulfate reducing bacteria are psychrotolerant as they were inhibited by low temperatures.
The Silurian Pelplin Formation is a part of a thick, mud-prone distal fill of the Caledonian foredeep, which stretches along the western margin of the East European Craton. The Pelplin Formation consists of organic carbon- rich mudstones that have recently been the target of intensive investigations, as they represent a potential source of shale gas. The Pelplin mudstones host numerous calcite concretions containing authigenic pyrite and barite. Mineralogical and petrographic examination (XRD, optical microscopy, cathodoluminoscopy, SEM-EDS) and stable isotope analyses (δ13Corg, δ13C and δ18O of carbonates, δ34S and δ18O of barite) were carried out in order to understand the diagenetic conditions that led to precipitation of this carbonate-sulfide-sulfate paragenesis and to see if the concretions can enhance the understanding of sedimentary settings in the Baltic and Lublin basins during the Silurian. Barite formed during early diagenesis before and during the concretionary growth due to a deceleration of sedimentation during increased primary productivity. The main stages of concretionary growth took place in yet uncompacted sediments shortly after their deposition in the sulfate reduction zone. This precompactional cementation led to preferential preservation of original sedimentary structures, faunal assemblages and early- diagenetic barite, which have been mostly lost in the surrounding mudstones during burial. These components allowed for the reconstruction of important paleoenvironmental conditions in the Baltic and Lublin basins, such as depth, proximity to the detrital orogenic source and marine primary productivity. Investigation of the concretions also enabled estimation of the magnitude of mechanical compaction of the mudstones and calculation of original sedimentation rates. Moreover, it showed that biogenic methane was produced at an early-diagenetic stage, whereas thermogenic hydrocarbons migrated through the Pelplin Formation during deep burial.
New measurement technologies, e.g. Light Detection And Ranging (LiDAR), generate very large datasets. In many cases, it is reasonable to reduce the number of measuring points, but in such a way that the datasets after reduction satisfy specific optimization criteria. For this purpose the Optimum Dataset (OptD) method proposed in  and  can be applied. The OptD method with the use of several optimization criteria is called OptD-multi and it gives several acceptable solutions. The paper presents methods of selecting one best solution based on the assumptions of two selected numerical optimization methods: the weighted sum method and the "-constraint method. The research was carried out on two measurement datasets from Airborne Laser Scanning (ALS) and Mobile Laser Scanning (MLS). The analysis have shown that it is possible to use numerical optimization methods (often used in construction) to obtain the LiDAR data. Both methods gave different results, they are determined by initially adopted assumptions and – in relation to early made findings, these results can be used instead of the original dataset for various studies.
The present paper addresses the analysis of structural vibration transmission in the presence of structural joints. The problem is tackled from a numerical point of view, analyzing some scenarios by using finite element models. The numerical results obtained making use of this process are then compared with those evaluated using the EN 12354 standard vibration reduction index concept. It is shown that, even for the simplest cases, the behavior of a structural joint is complex and evidences the frequency dependence. Comparison with results obtained by empirical formulas reveals that those of the standards cannot accurately reproduce the expected behavior, and thus indicate that alternative complementary calculation procedures are required. A simple methodology to estimate the difference between numerical and standard predictions is here proposed allowing the calculation of an adaptation term that makes both approaches converge. This term was found to be solution-dependent, and thus should be evaluated for each structure.
Additional sound sources are used as actuators in the vast majority of active noise reduction systems. One of the possible opportunities to extend the field of applications of active noise reduction systems is using active structures of variable sound insulation. The paper presents an analysis of ways of reducing noise with a structure of variable sound insulation consisting of a metal plate, active elements (Macro Fiber Composite), and a control system. The paper presents results of acoustic radiation simulations and measurements of sound intensity generated by the structure under the influence of stimulation by an acoustic wave. Simulations of mechanical vibrations and acoustic radiation for the plate were performed with the finite element method and ANSYS software. Simulation results made it possible to select locations for gluing the active elements and sensors. Analyses of the sound pressure level in the space to which the plate is radiating made it possible to determine dominant frequencies in the characteristics and, as a result, indicate vibration modes that can be reduced. Sound intensity measurements were performed with a three-way probe of USP mini Microflown. Results of simulations and measurements show that it is possible to achieve an improvement of the insulating power of a metal plate by approx. 10 dB.
FeCl3 bearing etching solution is mainly used for etching of metals used in shadow masks, PCBs and so on. Due course of Invar alloy etching process the FeCl3 bearing etching solution get contaminated with Ni2+ which affect adversely the etching efficiency. Hence, FeCl3 bearing etching solution discarded after several cycle of operation causes an environmental and economic problem. To address both the issues the etching solution was purified through solvent extraction and remained Ni2+ recovered by wet chemical reduction using hydrazine. For optimum Fe3+ extraction efficiency, various extraction parameter were optimized and size and morphology of the recovered pure Ni powder was analyzed. The reported process is a simple process to purify and recover Ni from industry etching solution.
In this study, the vibration analysis of fully and partially treated laminated composite Magnetorheological (MR) fluid sandwich plates has been investigated experimentally. The natural frequencies of fully and partially treated laminated composite MR fluid sandwich plates have been measured at various magnetic field intensities under two different boundary conditions. The variations of natural frequencies with applied magnetic field, boundary conditions and location ofMRfluid pocket have been explored. Further, a comparison of natural frequencies of fully and partially treated MR fluid sandwich structure has been made at various magnetic field intensities.
Three plants extracts were used for biosynthesis of Ag nanoparticles (AgNPs). AgNPs nucleation process requires effective reduction agents which secure Ag+ to Ag0 reduction and also stabilizing/capping agents. The UV-vis and TEM observation revealed that the best results were obtained by R. officinalis leaf extract. The strong SPR band peak appeared at the wavelength 418 nm. Synthetized AgNPs were globular, fine (~20 nm), uniform and stabile throughout the experiment. A rapid rate of AgNPs synthesis was also significant and economically advantageous factor. Fine (10-20 nm) and globular nanoparticles were synthetized also by U. dioica leaf extract, but the stability of nanoparticles was not permanent. Despite V. vitis-idaea fruit extract contains a lot of reducing agents, UV-vis did not confirm the presence of AgNPs in solution. Synthetized Ag particles were very unstable, Ag particles agglomerated very fast and clearly indicated sediment was formed.
Copper slag is a by-product obtained during smelting and refining of copper. Copper smelting slag typically contains about 1 wt.% copper and 40 wt.% iron depending upon the initial ore quality and the furnace type. Main components of copper slag are iron oxide and silica. These exist in copper slag mainly in the form of fayalite (2FeO ·SiO2). This study was intended to recover pig iron from the copper smelting slag by reduction smelting method. At the reaction temperature of below 1400°С the whole copper smelting slag was not smelted, and some agglomerated, showing a mass in a sponge form. The recovery behavior of pig iron from copper smelting slag increases with increasing smelting temperature and duration. The recovery rate of pig iron varied greatly depending on the reaction temperature.
Reduction of three industrial nickel oxides (Goro, Tokyo and Sinter 75) with a hydrogen bearing gas was revisited in the temperature interval from 523 to 673 K (250 to 400°C). A pronounced incubation period is observed in the temperature interval tested. This period decreases as the reduction temperature increases. Thermogravimetric data of these oxides were fitted using the Avrami-Erofeyev kinetic model. The reduction of these oxides is controlled by a nucleation and growth mechanism of metallic nickel over the oxides structure. Rate kinetic constants were re-evaluated and the activation energy for the reduction of these oxides was re-calculated.
The use of elastic bodies within a multibody simulation became more and more important within the last years. To include the elastic bodies, described as a finite element model in multibody simulations, the dimension of the system of ordinary differential equations must be reduced by projection. For this purpose, in this work, the modal reduction method, a component mode synthesis based method and a moment-matching method are used. Due to the always increasing size of the non-reduced systems, the calculation of the projection matrix leads to a large demand of computational resources and cannot be done on usual serial computers with available memory. In this paper, the model reduction software Morembs++ is presented using a parallelization concept based on the message passing interface to satisfy the need of memory and reduce the runtime of the model reduction process. Additionally, the behaviour of the Block-Krylov-Schur eigensolver, implemented in the Anasazi package of the Trilinos project, is analysed with regard to the choice of the size of the Krylov base, the blocksize and the number of blocks. Besides, an iterative solver is considered within the CMS-based method.
High distribution system power-losses are predominantly due to lack of investments in R&D for improving the efficiency of the system and improper planning during installation. Outcomes of this are un-designed extensions of the distributing power lines, the burden on the system components like transformers and overhead (OH) lines/conductors and deficient reactive power supply leading to drop in a system voltage. Distributed generation affects the line power flow and voltage levels on the system equipment. These impacts of distributed generation (DG) may be to improve system efficiency or reduce it depending on the operating environment/conditions of the distribution system and allocation of capacitors. For this purpose, allocating of distributed generation optimally for a given radial distribution system can be useful for the system outlining and improve efficiency. In this paper, a new method is used for optimally allocating the DG units in the radial distribution system to curtail distribution system losses and improve voltage profile. Also, the variation in active power load in the system is considered for effective utilization of DG units. To evidence the effectiveness of the proposed algorithm, computer simulations are carried out in MATLAB software on the IEEE-33 bus system and Vastare practical 116 bus system.
Silica multichannel monoliths modified with zirconia, titania and alumina have been used as reactive cores of microreactors and studied in chemoselective reduction (MPV) of cyclohexanon/benzaldehyde with 2-butanol as a hydrogen donor. The attachment of metal oxides to the silica surface was confirmed by FT–IR spectroscopy, and dispersion of metal oxides was studied by UV–Vis spectroscopy. the catalytic activity of the lewis acid centres in both chemical processes decreased in the order zirconia > alumina > titania. This activity is in good agreement with dispersion and coordination of metal species. good stability of zirconia-grafted reactors was confirmed. high porosity of the monoliths and the presence of large meandering flow-through channels with a diameter of ca. 30 mm facilitate fluid transport and very effective mixing in the microreactors. The whole synthesis process is perfectly in line with trends of modern flow chemistry
Results for microcrystalline cellulose pyrolysis are presented, which includes thermogravimetric measurements and kinetic analysis of experimental data. The effect of sample mass size and heating rate on estimated values of activation energy and pre-exponential factor is demonstrated and a simple modification of procedure is proposed that allows for the correct values of kinetic parameters regardless of the experimental conditions. The efficiency of the proposed method is confirmed for two endothermic chemical reactions. A method of nonlinear regression is used for calculation of kinetic parameters for a single or TG curve or several curves simultaneously.
The error reduction technique, based on inverse transformation, for a shunt active resistance measurement using an ammeter and voltmeter is considered. When computing a corrected reading only multiplicative operations on two measurement results are used, namely squaring and division. The proposed method allows to increase re-sistance measurement accuracy by about two orders of magnitude what has been validated by both theoretical and experimental outcomes.