The present paper is comparing the results of research studies carried out for three road acoustic screens of different design and different number of damping layers. For the tests, we selected timber or steel screens with a traditional multilayer structure and also one innovative type of simplified design. With respect to particular panels, their sound absorption properties were investigated in the reverberation chamber after they had been subjected to simulated weathering. In the process, two screens were subjected to the aging tests of 50–500 cycles in a special climatic chamber, and the innovative screens were subjected to 1000 cycles. The procedure was repeated every 50 or 100 cycles in order to obtain the changes of acoustic characteristics. The changes taking place in the absorbing material were also investigated with the use of scanning electron microscopy method (SEM). Basing on the obtained results and on the statistical analysis, the capability to maintain acoustic properties by the panels during their service life in natural conditions was estimated. For that purpose, linear statistical models were worked out, which were then applied to estimate the value of the single number sound absorption coefficient after successive aging cycles as well as the predicted time periods of acoustic class changes.
Sound absorption coefficient is a commonly used parameter to characterize the acoustic properties of sound absorbing materials. It is defined within the frequency range of 100-5 000 Hz. In the industrial conditions, many appliances radiating acoustic energy of the frequency range of above 5000 Hz are used and at the same time it is known that a noise within the frequency range of 5 000-50 000 Hz can have a harmful effect on people,hence there is a need to define the coefficient in this frequency range. The article presents a proposal for a method of measurement of the sound absorption coefficient of materials in the frequency range from 5 000 Hz to 50 000 Hz. This method is a modification of the reverberation method with the use of interrupted noise.
Recently, a new class of ceramic foams with porosity levels up to 90% has been developed as a result of the association of the gelcasting process and aeration of the ceramic suspension. This paper presents and discusses original results advertising sound absorbing capabilities of such foams. The authors man- ufactured three types of alumina foams in order to investigate three porosity levels, namely: 72, 88, and 90%. The microstructure of foams was examined and typical dimensions and average sizes of cells (pores) and cell-linking windows were found for each porosity case. Then, the acoustic absorption coefficient was measured in a wide frequency range for several samples of various thickness cut out from the foams. The results were discussed and compared with the acoustic absorption of typical polyurethane foams proving that the alumina foams with high porosity of 88-90% have excellent sound absorbing properties competitive with the quality of sound absorbing PU foams of higher porosity.
Characterization of sound absorbing materials is essential to predict its acoustic behaviour. The most commonly used models to do so consider the flow resistivity, porosity, and average fibre diameter as parameters to determine the acoustic impedance and sound absorbing coefficient. Besides direct experimental techniques, numerical approaches appear to be an alternative to estimate the material's parameters. In this work an inverse numerical method to obtain some parameters of a fibrous material is presented. Using measurements of the normal incidence sound absorption coefficient and then using the model proposed by Voronina, subsequent application of basic minimization techniques allows one to obtain the porosity, average fibre diameter and density of a sound absorbing material. The numerical results agree fairly well with the experimental data.
This paper presents the results of measurements of the sound absorption coefficient of auditorium seats carried out in the laboratory using two methods. In the first one, small blocks of seats in various arrangements were studied in a reverberation chamber to determine the absorption coefficient of an auditorium of infinite dimensions. The results were compared to the values of the absorption coefficient measured using the second method, which involved samples enclosed within a frame screening the side surfaces of other auditorium blocks. The results of both methods allowed for the assessment of the sound absorption coefficient of an auditorium of any dimensions while taking into account the sound absorption by the side surfaces. The method developed by the authors will simplify the currently known measurement procedures.
The sound absorption property of polyurethane (PU) foams loaded with natural tea-leaf fibers and luffa cylindrica (LC) has been studied. The results show a significant improvement in the sound absorption property parallel to an increase in the amount of tea-leaf fibers (TLF). Using luffa-cylindrica as a filler material improves sound absorption properties of soft foam at all frequency ranges. Moreover, an increase in the thickness of the sample resulted in an improvement of the sound absorption property. It is pleasing to see that adding tea-leaf fibers and luffa-cylindrica to the polyurethane foam demonstrate a significant contribution to sound absorption properties of the material and it encourages using environmental friendly products as sound absorption material in further studies.
Macroporous silica fibers having spherical cavities were fabricated by electrospinning using the spinning solution prepared from the mixed dispersion of tetraethylorthosilicate (TEOS) and polystyrene nanospheres as precursor and sacrificial templates, respectively, by injection through metallic nozzle. By applying electric field, the electro-spun fibers obtained by evaporation-driven self-assembly were collected on flat substrate or rotating drum, followed by the removal of the templates by calcination. The sound absorption coefficient of the porous fibers was measured by impedance tube, and the measured value was larger than 0.9 at high frequency region of incident waves. The surface of the resulting fibers was modified using fluorine-containing silane coupling agent to produce superhydrophobic fibrous materials to prevent the infiltration of humidity.
Efficient ultrasonic noise reduction by using enclosures requires the knowledge of absorbing properties of materials in the frequency range above 4 kHz. However, standardized methods enable determination of absorption coefficients of materials in the frequency range up to 4 kHz. For this reason, it is proposed to carry out measurements of the sound absorption properties of materials in the free field by means of a tone-burst technique in the frequency range from 4 kHz to 40 kHz at angles of incidence varying from 0° to 60°. The absorption coefficient of a material is calculated from the reflection coefficient obtained by reflecting a tone-burst from both a perfectly reflecting panel and a combination of this panel and the sample of the tested material. The tests results show that mineral wool and polyurethane open-cell foam possess very good absorbing properties in this frequency range.
The area of environmental protection concern minimises the impact that technical objects have on the environment. Usually the most effective way of protecting the environment is to influence the source of the problem. For this reason studies are conducted to modify the construction of machines, power machines in particular, so as to minimise their impact on the environment. In the case of environmental protection from noise it is most convenient to carry out measurements in an anechoic chamber. Unfortunately, this is possible only in very limited circumstances. In all other cases measurements are performed using an engineering method or the survey method, both of which are described in the standards and by taking into account the so-called environmental corrections. The obtained results are burdened with greater error than those of measurements in an anechoic chamber. Therefore, it would seem advantageous to develop a method of obtaining similar and reliable results as those in an anechoic chamber, but in a reverberant field. The authors decided to use numerical modelling for this purpose. The main objective of this work is a comprehensive analysis of the numerical model of a laboratory designed for acoustic tests of selected power machines. The geometry of a room comprising an area of analysis is easy to design. The main difficulty in modelling the phenomena occurring in the analysed area can be the lack of knowing the boundary conditions. Therefore, the authors made an attempt to analyse the sensitivity of various acoustic parameters in a room in order to change these boundary conditions depending on the sound absorption coefficient
Considering the environmental pollution caused by waste rubber, some measures should be taken to improve the utilization rate of waste rubber. In this study, the effect of Ethylene Propylene Diene Monomer (EPDM) particles in the polyurethane (PU) foams on sound absorption behavior is investigated for improving sound environment within vehicles and reducing the environment pollution. EPDM of different contents and hardness are used as fillers for producing foams with different pore morphologies and sound absorption properties. The results show adds EPDM to foam would produce smaller pores, higher density and bigger air-flow resistivity. Simultaneously, there are better sound absorption properties of the PU foam composites in the medium frequency region and the better value can be obtained at the lower frequency with the content of EPDM increasing. The hardness of EPDM also shows better influence on sound absorption properties, especially in the medium frequency region. It means the foam pore morphologies have influence on sound absorption properties.
In this work we present the design and the manufacturing processes, as well as the acoustics standardization tests, of an acoustic barrier formed by a set of multi-phenomena cylindrical scatterers. Periodic arrangements of acoustic scatterers embedded in a fluid medium with different physical properties are usually called Sonic Crystals. The multiple scattering of waves inside these structures leads to attenuation bands related to the periodicity of the structure by means of Bragg scattering. In order to design the acoustic barrier, two strategies have been used: First, the arrangement of scatterers is based on fractal geometries to maximize the Bragg scattering; second, multi-phenomena scatterers with several noise control mechanisms, as resonances or absorption, are designed and used to construct the periodic array. The acoustic barrier reported in this work provides a high technological solution in the field of noise control.