Maintaining railway turnout operability is crucial for ensuring railway transport safety. Electric heating of railway turnouts is a significant technical and economic issue. The classical heating is characterised by high power consumption. For this reason, research is needed to optimise the current system. This paper presents results of a numerical analysis and of experimental researches. The numerical analysis was carried out using the ANSYS software. There was conducted a numerical comparative analysis of energy loss during heating performed using two different heaters. Including the classical method and a heater thermally insulated from a rail. In the first step, heating of a working space filled with a substitute snow model was considered. The snow-covered surface area was held within the working space of the turnout. It was assumed that the snow substitute material had thermal properties approximately the same as real light snow. It was also assumed that the material is in the solid state which would not undergo a phase change. In the next step, a real snow model that included the phase change process was taken into account. The energy efficiency and heat distribution in the turnout have been analysed and compared. The experimental researches were carried out in a physical model. The results showed that the use of a contactless heater results in creating a larger area over which emitted heat affected snow in the working space. Consequently, more snow was melted around the contactless heater than the classic one. This experimental observation supported the results of the numerical analyses presented previously.
For the optimal location of an additional surplus measurements in the design of redundant measurements system, from data reconciliation point of view, of thermal processes, an information entropy has been applied. The relative entropy - Kullback-Leibler divergence, has been used. As a criterion of the optimal location of an additional surplus measurements in a system of measurements data, the minimum of the entropy information of reconciled measurements data has been assumed. Hence, the objective function in the described optimization task is maximum of the relative entropy - Kullback-Leibler divergence concerning sets of raw and reconciled measurements data. Simulation calculation with application of data reconciliation algorithm and Monte Carlo method concerning the influence of installation of the additional surplus measurements on decrease of entropy information of measurements after data validation have been carried out. The example calculations concerned the cross high-pressure heat regeneration system with cascade flow of condensate installed in 153 MW power unit equipped with cooler of steam are presented. Calculations for all variants of configurations of an additional surplus measurements in the analyzed thermal system have been done. Usefulness of the proposed Kullback-Leibler divergence as a objective function has been demonstrated.
Biomass is commonly considered as a renewable fuel, which taking into account emission of CO2 does not contribute to the emission of the greenhouse gases. In the research, combustion tests of two types of fuel formed on the basis of straw with addition of polyethylene were performed in the laboratory. The article presents results of measurements of gas pollution coming from the combustion of the formed fuel. Obtained results were compared with similar literature data for the combustion of coal. The research covers also testing of chemical content, content of heavy metals and selected physical properties of ashes generated during the process of burning fuel based on straw.
The main task of mathematical modelling of thermal and flow processes in vertical ground heat exchanger (BHE-Borehole Heat Exchanger) is to determine the unit of borehole depth heat flux obtainable or transferred during the operation of the installation. This assignment is indirectly associated with finding the circulating fluid temperature flowing out from the U-tube at a given inlet temperature of fluid in respect to other operational parameters of the installation. The paper presents a model of thermal and flow processes in BHE consisting of two analytical models separately-handling processes occurring inside and outside of borehole. A quasi-three-dimensional model formulated by Zeng was used for modelling processes taking place inside the borehole and allowing to determine the temperature of the fluid in the U-tube along the axis of BHE. For modelling processes occurring outside the borehole a model that uses the theory of linear heat source was selected. The coupling parameters for the models are the temperature of the sealing material on the outer wall of the borehole and the average heat flow rate in BHE. Experimental verification of the proposed model was shown in relation to BHE cooperating with a heat pump in real conditions.
According to the analysis of the current state of the knowledge shows that there is little information on the process of phase transformations that occur during the cooling Cu-Al-Fe-Ni hypo-eutectoid bronzes with additions of Cr, Mo and/or W, made additions individually or together, for the determination of: the type of crystallizing phases, crystallizing phases, order and place of their nucleation. On the basis of recorded using thermal and derivative analysis of thermal effects phases crystallization or their systems, analysis of the microstructure formed during crystallization - observed on the metallographic specimen casting ATD10-PŁ probe, analysis of the existing phase equilibrium diagrams forming elements tested Cu-Al-Fe-Ni bronze, with additions of Cr, Mo, W and/or Si developed an original model of crystallization and phase transformation in the solid state, the casting of high quality Cu-Al-Fe-Ni bronze comprising: crystallizing type phase, crystallizing phase sequence, place of nucleation.