Search results

Filters

  • Journals
  • Date

Search results

Number of results: 15
items per page: 25 50 75
Sort by:

Abstract

The article presents the results of selected energy parameters calculations, carried out for the recorded values of instantaneous voltages and currents in the three-phase power supply of the model vibratory unit. The parameters were the values of active and apparent power taken from the drive consisting of two electric motors supplied by the inverter for selected frequency settings and directly from the power grid. In addition, calculations of tgφ power factor values were made to evaluate the compensation of reactive power consumption in the tested power systems. Measurements and calculations lead to the conclusion that if the frequency of the inverter output voltage rises, the active and apparent power consumed by the model vibratory drive unit increases. The active and apparent power for setting the output frequency of the inverter from 50 Hz was less than the active and apparent power taken by the model vibratory unit that was powered directly from the power grid. The power factor tgφ in the power supply system was approximately 6, except one case (f = 30 Hz).
Go to article

Abstract

In the present paper, we investigate a multi-server Erlang queueing system with heterogeneous servers, non-homogeneous customers and limited memory space. The arriving customers appear according to a stationary Poisson process and are additionally characterized by some random volume. The service time of the customer depends on his volume and the joint distribution function of the customer volume and his service time can be different for different servers. The total customers volume is limited by some constant value. For the analyzed model, steady-state distribution of number of customers present in the system and loss probability are calculated. An analysis of some special cases and some numerical examples are attached as well.
Go to article

Abstract

This study summarises the research efforts undertaken in iron foundry plants in which the process are mostly automated and mechanised. The research program was limited in scope, focusing on causes of surface defects in castings products that are attributable to the bentonite-containing sand and the mould system. One of the potential roots of surface defects is heterogeneity of sand grains, containing lumped ball-shaped grains and irregular pellets with a layered-structure. The moisture contents of those lumped grains is different than the moisture level required in the process, besides these grains may contain various elements and metallic compounds which, when cast into moulds, may react with molten metals in an uncontrolled manner. As a result, surface defects are produced, such as surface blowholes, burst penetration, sand holes, slag inclusions, pinhole porosity. This study investigated the efficiency of key sand preparation and moulding machines and installations integrated into the casting process line. The efficiency of machines and installations is defined in terms of quality parameters of sand mix and moulds, which are associated with the emergence of surface defects on castings.
Go to article

Abstract

Design of a compressed air system is a complex issue, involving the design of structures formed by the air sources, air receptors and installations connecting all structure components. Another major task is to ensure the required quality of compressed air. The paper briefly outlines the methodology of integrated and network structure design, using an objective function to find the optimal solution. In terms of quality assurance, the technological aspects of compressed air generation, treatment and distribution are defined.
Go to article

Abstract

The paper outlines the methodology of virtual design of a foundry plant as a system. The most important stage in the procedure involves the development of a model defined as a set of data about the system. Model development involves two stages: defining the model’s architecture and specifying the model data in the form of parameters and input-output relationships. The structure is understood as configuration of machines and transport units, representing the sub-systems and system components. As the main purpose of the simulation procedure is to find the characteristics of the system’s behaviour, the merits of the iterative method involving analysis, synthesis and evaluation of results are fully explored.
Go to article

Abstract

Vacuum conditions in foundry installations are generated using electric-driven vacuum pumps. The purpose of the experiment is to evaluate the performance of a vacuum-assisted system for compaction of moulding sand basing on registered plots of selected electric power parameters of the power-supplying system of the pumps. Model testing done on an experimental vacuum system installation, power-supplied from a system incorporating the recorders of instantaneous current and voltage values. Following the numerical procedure, the experimental data are analysed to yield mathematical relationships between the variations of the generated vacuum pressure levels and variations of selected electric power parameters. Registered and computed values of selected parameters: instantaneous and RMS voltage and current values, active, reactive and apparent power levels and power coefficient allow for diagnosing the adequacy and reliability of the system operation. According to the authors, the applied monitoring of the power parameters of a vacuum-assisted installation may become an effective and easy practical method of evaluating the performance of such installations, used also in foundry plants.
Go to article

Abstract

Shot blasting machines are widely used for automated surface treatment and finishing of castings. In shot blasting processes the stream of shots is generated and shaped by blasting turbines, making up a kinetic and dynamic system comprising a separating rotor, an adapting sleeve and a propelling rotor provided with blades. The shot blasting performance- i.e. the quality of shot treated surfaces depends on the actual design and operational parameters of the unit whilst the values of relevant parameters are associated with the geometry of turbine components and the level of its integration with the separator system. The circulation of the blasting medium becomes the integrating factor of the process line, starting from the hopper, through the propeller turbine, casting treatment, separation of contaminated abrasive mixture, to its recycling and reuse. Inferior quality of the abrasive agent (shot) and insufficient purity of the abrasive mixture are responsible for low effectiveness of shot blasting. However, most practitioners fail to fully recognize the importance of proper diagnostics of the shot blasting process in industrial conditions. The wearing of major machine components and of the blasting agent and quality of shot treated surfaces are often misinterpreted, hence the need to take into account all factors involved in the process within the frame of a comprehensive methodology. This paper is an attempt to formulate and apply the available testing methods to the engineering practice in industrial conditions.
Go to article

Abstract

In this article the main problems related with the proper choice of the design and operation parameters of vacuum installation in vacuum moulding system have been discussed. In such system a vacuum are generated using electric-driven vacuum pumps. The aim of the experiment is to evaluate the performance of a vacuum system basing on registered plots of selected electric power parameters of the power-supplying system of the pumps with parallel measurements instantaneous values of pressure in selected points of model stand. The measurements system for power-supply unit has incorporated the recorders of instantaneous current and voltage values. Following the suitable numerical procedure, the experimental data are analysed to yield mathematical relationships between the variations of the generated vacuum pressure levels and variations of selected electric power parameters. According to the authors, the applied measurements system of the parameters of a vacuum-assisted installation may become an effective and easy practical method of evaluating the performance of such installations, used also in industry.
Go to article

Abstract

The aim of the present study was to investigate whether the anterior chamber constitutes part of the normal migratory pathway of CD4+ and CD8+ lymphocytes in cattle and swine. The cells obtained from aqueous humor of cows and pigs were stained for CD4 and CD8 receptors, and subsequently analyzed with flow cytometry. The mean percentage of CD4+CD8-, CD4-CD8+ and CD4+CD8+ cells within the total lymphocyte population of the bovine anterior chamber was, respectively, 17.88, 12.64 and 27.26%. In turn, the mean values of these parameters in pigs were 1.77, 38.48 and 17.45, respectively. Among bovine and porcine CD4+CD8+ cells prevalent were those displaying CD4lowCD8low and CD4lowCD8high phenotypes, respectively. The results suggest that the anterior chamber in cattle and swine is an element in the normal migratory pathway of CD4+, CD8+ and CD4+CD8+ cells. Furthermore, the contribution of these subsets in the anterior chamber lymphocyte population can differ considerably between animal species.
Go to article

This page uses 'cookies'. Learn more