The aim of the conducted research was to determine the possibilities of using the biomass of macroalgae obtained from Puck Bay during May-September season in biogas production process. Model respirometry chambers were used to determine the amount of produced biogas and examine its quality composition. Depending on the month in which the algal biomass was obtained, the experiments were divided into five stages. In each stage, the effectiveness of the biogas production process was tested for the applied loads in model fermentation chambers in the range from 1.0 kg DOM/m3 · d to 3.0 kg DOM/m3 · d. During the experiments it was found that the efficiency of biogas production varied from 205 dm3/kg DOM to 407 dm3/kg DOM depending on the month of the vegetation season and the applied organic matter load in the chamber. Methane content was very high and ranged from 63% to 74%.
The objective of this study was to determine the effect of advanced oxidation process with the use of Fenton’s reaction on the effectiveness of anaerobic treatment of wastewaters originating from the wood industry that were characterized by a high concentration of formaldehyde. Experiments were established to analyze changes in COD content and in the concentration of formaldehyde in treated wastewaters, additional analyses were carried out to assay quantitative and qualitative changes in the biogas produced. The first stage of the experiment involved analyses of the effectiveness of the tested wastewaters treatment only in the process of methane fermentation. At the second stage of the experiment, the biological process was preceded by chemical pre-treatment of wastewaters with Fenton’s reagent. The conducted study proved that the investigated variants of chemical pre-treatment of wastewaters had a significant effect on increasing the total biogas production. In contrast, no significant effect of the applied technology was demonstrated on changes in the concentration of the analyzed contaminants in the treated wastewaters.
Chlorophyll a content and the density and species composition of algae were determined in drifting sea ice north of the Elephant Island (between 54-56°W and 60°30'—61°00'S) at the end of October 1986. In yellow-brownish pieces of brash ice the amount of chlorophyll α was on average 203.5 ± 149.9 mg m-3 at the density of algal cells of 255.7+137.8-103 in cm3. In not visibly discoloured ice the respective values were about 80 times lower, and in surface water about 700 times lower. 69 algal taxa were recorded in the samples, almost all of which were diatoms. Nitzschia cylindrus dominated in all the samples. A comparison of species composition in the investigated habitats revealed that the highest species similarities occurred between samples collected in discoloured ice, lower in the uncoloured ice and the lowest ones in water.
Three methods of estimating radii of spray droplets are discussed and results of their practical application in the case of explosively produced water spray are reported. Parameters of model radii distributions are fitted using the least squares method. Finally, the data obtained for a number of tests are used for estimating fraction of explosion energy used for pulverization of water in the process of explosive production of water-spray.
The paper presents precipitation results from cold thermal water deposits that are the main cause of clogging in absorbent geothermal wells and borehole areas. As a result of physical and chemical analysis, laboratory tests and observation of the operation of a geothermal installation, a new method was developed to prevent the precipitation of sludge from cooled thermal water. The method being a modification of soft acidising was tentatively named as a super soft acidising method
Recently, a new class of ceramic foams with porosity levels up to 90% has been developed as a result of the association of the gelcasting process and aeration of the ceramic suspension. This paper presents and discusses original results advertising sound absorbing capabilities of such foams. The authors man- ufactured three types of alumina foams in order to investigate three porosity levels, namely: 72, 88, and 90%. The microstructure of foams was examined and typical dimensions and average sizes of cells (pores) and cell-linking windows were found for each porosity case. Then, the acoustic absorption coefficient was measured in a wide frequency range for several samples of various thickness cut out from the foams. The results were discussed and compared with the acoustic absorption of typical polyurethane foams proving that the alumina foams with high porosity of 88-90% have excellent sound absorbing properties competitive with the quality of sound absorbing PU foams of higher porosity.
This paper presents the method for determination of the time of further safe service for welded joints of boiler components after exceeding the design work time. The evaluation of the life of the parent material and its welded joints was performed. Microstructure investigations using a scanning electron microscope, investigations of strength properties, impact testing, hardness measurements and abridged creep tests of the basic material and welded joints were carried out. The investigations described in this paper allowed the time of further safe service of the examined components made of 13CrMo4-5 steel to be determined. The method for determination of the time of safe service of boiler components working under creep conditions allows their operation beyond the design service life. The obtained results of investigations are part of the materials database developed by the Institute for Ferrous Metallurgy.