The publication presents a novel concept of the process of plastic forming of variable longitudinal-section cylindrical products, being the subject of Patent Application P.427426 . Additionally, these products are provided with a connection stub pipe. The plastic forming method proposed in the article combines many advantages and utilitarian benefits associated with the manufacturing technology itself, as well as with its further implementation. Using stock in the form of normalized bar commonly available in the metal product market as a finished product obviously reduces the process costs involved with stock preparation, i.e. casting, rolling, machining, etc. It also results in obtaining a much smaller surface area of stock contact with the tool and, as a consequence, a smaller surface of stock friction against the tool, which contributes to a reduction of force needed for the plastic forming of the product. The smaller contact surface area and the shorter time of stock contact with the cooler tool cause, above all, less intensive heat exchange and stock chilling. This has a significant effect on the plasticity of the cast material and, as a consequence, the plastic forming force. The proposed method enables also manufacturing cylinders with either a closed or open stub pipe with a regulated length and a varying section. In addition, unlike the method known from Polish Patent Specification PL 212062 , the proposed method does not require using a multi-tool press. The upper punch is furnished with a flange, whose job is to start the stock extruding sleeve at the next process stage.
The paper presents the summary of research on polymer melt particle motion trajectories in a disc zone of a screw-disk extruder. We analysed two models of its structure, different in levels of taken simplifications. The analysis includes computer simulations of material particle flow and results of experimental tests to determine the properties of the resultant extrudate. Analysis of the results shows that the motion of melt in the disk zone of a screw-disk extruder is a superposition of pressure and dragged streams. The observed trajectories of polymer particles and relations of mechanical properties and elongation of the molecular chain proved the presence of a stretching effect on polymer molecular chains.
The article proposes the implementation of a novel method of plastic forming of internal toothing in flange spline sleeves. A method being the subject of Polish patent application P.416772 has been used for this purpose, which involves a combination of the scheme of the direct extrusion of a cone hollow with the die press forming of the wall to obtain a flange. The entire process takes place in a single technological sequence. The operations come one after another, so that there is no need for reheating the stock or carrying out intermediate soft annealing. The proposed method is assumed to be an alternative to the operation of press forming of internal spline sleeve toothing in a conical die  and to the operation of swaging on rotary swaging machines . It is assumed that this method, too, is alternative to other technologies known from the literature and industrial practice, whose specifications and literature references will be indicated later on in this paper. Computer simulations of the flanged sleeve plastic forming process were performed using the commercial numerical program Forge®3D. During the numerical computations, the distributions of temperature fields were determined on the cross-section of the plastically formed product. The computations enabled also the visualization of the plastic flow of metal, especially in the toothing forming regions, and the determination of the energy and force parameters of the process.
The study attempts to investigate the influence of severe plastic deformation (SPD in the hydrostatic extrusion (HE) process on the anisotropy of the structure and mechanical properties of the AA 6060 alloy. Material in isotropic condition was subjected to a single round of hydrostatic extrusion with three different degrees of deformation (ε = 1.23, 1.57, 2.28). They allowed the grain size to be fragmented to the nanocrystalline level. Mechanical properties of the AA 6060 alloy, examined on mini-samples, showed an increase in ultimate tensile strength (UTS) and yield strength (YS) as compared to the initial material. Significant strengthening of the material results from high grain refinement in transverse section, from »220 μm in the initial material to »300 nm following the HE process. The material was characterized by the occurrence of structure anisotropy, which may determine the potential use of the material. Static tensile tests of mini-samples showed »10% anisotropy of properties between longitudinal and transverse cross-sections. In the AA6060 alloy, impact anisotropy was found depending on the direction of its testing. Higher impact toughness was observed in the cross-section parallel to the HE direction. The results obtained allow to analyze the characteristic structure created during the HE process and result in more efficient use of the AA 6060 alloy in applications.
As-cast Mg-6Li-0.3Zn-0.6Y and Mg-6Li-1.2Zn-1.2Y (wt%) alloys were prepared and extruded at 260 oC with an extrusion ratio of 25. The microstructure and mechanical behavior of as-cast and extruded alloys are reported and discussed. The results show that Mg-6Li-1.2Zn- 1.2Y alloy is composed of α-Mg, β-Li, and W-Mg3Zn3Y2 phases while Mg-6Li-0.3Zn-0.6Y alloy contains α-Mg, β-Li, W-Mg3Zn3Y2 phase and X-Mg12ZnY. After hot extrusion, the microstructure of specimens is refined and the average grains size of extruded alloys is 15 μm. Dynamic recrystallization occurs during the extrusion, leading to grain refinement of test alloys. Both the strength and elongation of test alloys are improved by extrusion. The extruded Mg-6Li-0.3Zn-0.6Y alloy possesses an ultimate strength of 225 MPa with an elongation of 18% while the strength and elongation of Mg-6Li-1.2Zn-1.2Y alloy are 206 MPa and 28%, respectively. The X-phase in Mg-6Li-0.3Zn- 0.6Y is beneficial to the improvement of strength, but will lead to the decrease of ductility.
Trace elements Co, Cr were added to investigate their influence on the microstructure and physical properties of Al-Si extruded alloy. The Co, Cr elements were randomly distributed in the matrix, forms intermetallic phase and their existence were confirmed by XRD, EDS and SEM analysis. With addition of trace elements, the microstructure was modified, Si particle size was reduced and the growth rate of β-(Al5FeSi) phase limited. Compared to parent alloy, hardness and tensile strength were enhanced while the linear coefficient of thermal expansion (CTE) was significantly reduced by 42.4% and 16.05% with Co and Cr addition respectively. It is considered that the low CTE occurs with addition of Co was due to the formation of intermetallic compound having low coefficient of thermal expansion. The results suggested that Co acts as an effective element in improving the mechanical properties of Al-Si alloy.
The article presents tests results of metalforming of magnesium alloy AZ61. Materials for tests were ingots sized 40×90 mm from magnesium alloy marked with symbol AZ61. Before the shaping process the ingots underwent heat treatment. As a result of conduction of the deformation processes there were rods achieved with diameter of 8 mm. There were axisymmetrical compression tests conducted on the samples taken from rods in temperature range from RT to 350ºC in order to determine the plasticity and formability of the alloy AZ61. Static tensile test was conducted in room temperature (RT), in 300ºC and in 350ºC. With the use of light and electron microscopy techniques the changes which occurred in the microstructure of AZ61alloy in initial condition and after plastic deformation (classic extrusion, KoBo method extrusion) were described. The deformation of alloy AZ61 using the KoBo method contributes to an increase in strength and plastic properties. The effect of superplastic flow was found at a temperature of 350ºC, where a 300% increase in plastic properties – elongation value was obtained. The analysis of the microstructure showed a significant grain size reduction in the microstructure of alloy AZ61 after deformation by the KoBo method and after an axisymmetric compression test, where grains of an average diameter of d = 13 µm were obtained.