Coal reserves in the Czech Republic are estimated to be 10 billion tons – hard coal about 37%, brown coal about 60% and lignite 3%. Hard coal is produced in Northern Moravia. In 2017 the production of hard coal was 5.5 million tons. Brown coal is mined in North-Western Bohemia − the production of brown coal in 2017 was 38.1 million tons. Significant quantities of hard coal are exported to: Slovakia, Austria, Germany and Hungary. In accordance with the National Energy Policy, coal will remain the main source of energy in the country in the future, despite the increased use of nuclear energy and natural gas. The government expects that in 2030 energy from coal will account for 30.5% of energy produced. There are five coal companies in the Czech Republic: OKD, a.s., the only hard coal producer and four brown coal mining companies: Severočeské Doly a.s., owned by ČEZ, the largest producer of brown coal, Vršanská uhelná a.s., with coal resources until 2055, Severní energetická a.s. with the largest brown coal reserves in the Czech Republic and Sokolovska uhelná a.s., the smallest mining company extracting lignite. OKD operates coal in two mines Kopalnia Důlní závod 1 – (consists of three mines: ČSA Mine, Lazy Mine, Darkov Mine) and Mine Důlní závod 2 (ttwo mines Sever, Jih). The article also presents a pro-ecological solution for the management of waste heaps after coal enrichment – a plant for the enrichment of coal waste from the Hermanice heap.
Coal combustion processes are the main source of mercury emission to the environment in Poland. Mercury is emitted by both power and heating plants using hard and brown coals as well as in households. With an annual mercury emission in Poland at the level of 10 Mg, the households emit 0.6 Mg. In the paper, studies on the mercury release in the coal and biomass combustion process in household boilers were conducted. The mercury release factors were determined for that purpose. For the analyzed samples the mercury release factors ranged from 98.3 to 99.1% for hard coal and from 99.5% to 99.9% for biomass, respectively. Due to the high values of the determined factors, the amount of mercury released into the environment mainly depends on the mercury content in the combusted fuel. In light of the obtained results, the mercury content in the examined hard coals was 6 times higher than in the biomass (dry basis). Taking the calorific value of fuels into account, the difference in mercury content between coal and biomass decreased, but its content in coal was still 4 times higher. The mercury content determined in that way ranged from 0.7 to 1.7 μg/MJ for hard coal and from 0.1 to 0.5 μg/MJ for biomass, respectively. The main opportunity to decrease the mercury emissions from households is offered by the use of fuels with a mercury content that is as low as possible, as well as by a reduction of fuel consumption. The latter could be obtained by the use of modern boilers as well as by the thermo-modernization of buildings. It is also possible to partially reduce mercury emissions by using dust removal devices.
The aim of this study was to determine to what extent the ions present in hard water (125 mg/L of MgCl2 and 500 mg/L of CaCl2) may intensify the feed-induced decrease in oxytetracycline (OTC) absorption rate in broiler chickens after single oral administration at a dose of 15 mg/kg. Drug concentrations in plasma were determined by liquid chromatography-tandem mass spectrometry and combined, compartmental and non-compartmental approach was used to assess OTC pharmacokinetics. The administration of feed decreased the absolute bioavailability (F) of OTC from 12.70%±4.01 to 6.40%±1.08, and this effect was more pronounced after the combined administration of OTC with feed and hard water (5.31%±0.90). A decrease in the area under the concentration- time curve (AUC0-t), (from 10.18±3.24 μg·h/ml in control to 5.13 μg·h/ml±1.26 for feed and 4.26 μg·h/ml±1.10 for feed and hard water) and the maximum plasma concentration of OTC (Cmax) (from 1.22±0.18 μg/ml in control, to 1.01 μg/ml ±0.10 for hard water, 0.68 μg/ml±0.10 for feed and 0.61 μg/ml±0.10 for feed and hard water) was observed. The results of this study indicate that feed strongly decreases F, AUC0-t and Cmax of orally administered OTC. The ions present in hard water increase this inhibitory effect, which suggests that, therapy with OTC may require taking into account local water quality and dose modification, particularly when dealing with outbreaks caused by less sensitive microorganisms.
The objective of the submitted paper is to analyze the influence of the load on the calibration of micro-hardness and hardness testers. The results were validated by Measurement Systems Analysis (MSA), Analysis of Variance (ANOVA) and Z-score. The relationship between the load and micro-hardness in calibration of micro-hardness testers cannot be explained by Kick's Law (Meyer's index "n" is different from 2). The conditions of Kick's Law are satisfied at macro-hardness calibration, the values of "n" are close to 2, regardless of the applied load. The apparent micro-hardness increases with the increase of the load up to 30 g; the reverse indentation size effect (ISE) behavior is typical for this interval of the loads. The influence of the load on the measured micro-hardness is statistically significant for majority of calibrations.
The coal fed to gravity enrichment consists of coals coming from different deposits and exploitation fronts. These coals differ in quality parameters, especially the amount of gangue (stone) changing over time. This results in the instability of work, especially jiggers, which have a relatively low accuracy assessed by probable scattering or imperfection rates. This deteriorates the quality of the concentrate obtained, the quality parameters of which change over time. The improvement of jiggers work would be possible by averaging the feed. This process is practically impossible due to the failure to design such a node during plant construction, which are, in most cases, directly related to the shaft. In the article, the authors propose to solve the process of averaging the feed before directing it to the enrichment process in jiggers by introducing its deshaling in vibratory- air separators of the FGX type.
The implementation of EU environmental regulations in the energy sector is challenging for the power industry of its member states. The main role is played by documents such as the Winter Package and, especially, the Directive of the European Parliament and of the Council on the emission limits of certain pollutants and the implementation of BAT conclusions in order to achieve the EU’s decarbonization objectives. These regulations impose a greater need to control harmful substances emitted to the atmosphere while using fossil fuels, including hard coal, which is the main fuel for domestic units. At the same time, the decline in domestic fossil fuel production and decrease in the quality of parameters of the hard coal makes it difficult to purchase the proper fuel for power plants. As a consequence, the costs of hard coal increase. The article presents the concept of a mathematical model that can be applied for the optimization of coal supplies. The employment of this model allows one to achieve cost reductions. One of the advantages of the proposed tool, in addition to minimizing the cost of purchase and use of hard coal, is its rational management, especially for companies producing and using hard coal.
Improvement of Al-Si alloys properties in scope of classic method is connected with change of Si precipitations morphology through: using modification of the alloy, maintaining suitable temperature of overheating and pouring process, as well as perfection of heat treatment methods. Growing requirements of the market make it necessary to search after such procedures, which would quickly deliver positive results with simultaneous consideration of economic aspects. Presented in the paper shortened heat treatment with soaking of the alloy at temperature near temperature of solidus could be assumed as the method in the above mentioned understanding of the problem. Such treatment consists in soaking of the alloy to temperature of solutioning, keeping in such temperature, and next, quick quenching in water (20 0 C) followed by artificial ageing. Temperature ranges of solutioning and ageing treatments implemented in the adopted testing plan were based on analysis of recorded curves from the ATD method. Obtained results relate to dependencies and spatial diagrams describing effect of parameters of the solutioning and ageing treatments on HB hardness of the investigated alloy and change of its microstructure. Performed shortened heat treatment results in precipitation hardening of the investigated 320.0 alloy, what according to expectations produces increased hardness of the material.
The welding technologies are widely used for design of protection layer against wear and corrosion. Hardfacing, which is destined for obtaining coatings with high hardness, takes special place in these technologies. One of the most effective way of hardfacing is using self shielded flux cored arc welding (FCAW-S). Chemical composition obtained in flux cored wire is much more rich in comparison to this obtained in solid wire. The filling in flux cored wires can be enriched for example with the mixture of hard particles or phases with specified ratio, which is not possible for solid wires. This is the reason why flux cored wires give various possibilities of application of this kind of filler material for improving surface in mining industry, processing of minerals, energetic etc. In the present paper the high chromium and niobium flux cored wire was used for hardfacing process with similar heat input. The work presents studies of microstructures of obtained coatings and hardness and geometric properties of them. The structural studies were made with using optical microscopy and X- ray diffraction that allowed for identification of carbides and other phases obtained in the structures of deposited materials. Investigated samples exhibit differences in coating structures made with the same heat input 4,08 kJ/mm. There are differences in size, shape and distribution of primary and eutectic carbides in structure. These differences cause significant changes in hardness of investigated coatings.
Mechanical properties and residual stresses of friction stir welded and autogenous tungsten inert gas welded structural steel butt welds have been studied. Friction stir welding (FSW) of structural steel butt joints has been carried out by in-house prepared tungsten carbide tool with 20 mm/ min welding speed and 931 rpm tool rotation. Tungsten inert gas (TIG) welding of the butt joints was carried out with welding current, arc voltage and the welding speed of 140 amp, 12 V and 90 mm/min respectively. Residual stress measurement in the butt welds has been carried out in weld fusion zone and heat affected zone (HAZ) by using blind hole drilling method. The magnitude of longitudinal residual stress along the weld line of TIG welded joints were observed to be higher than friction stir welded joint. In both TIG and FSW joints, the nature of longitudinal stress in the base metal was observed to be compressive whereas in HAZ was observed to be tensile. It can be stated that butt welds produced with FSW process had residual stress much lower than the autogenous TIG welds.
The work presents the test result of the influence of cooling rate on the microstructure of AZ91 alloy, Vickers micro-hardness and Brinell hardness. Studies cooling and crystallization of AZ91 alloy was cast into the ceramic shells pre-heated to 180 ° C and then air-cooled at ambient temperature or intensively super cooled in the liquid coolant. The TDA method was applied to record and characterize the thermal effect resulting from the phase transformations occurring during the crystallization of AZ91 alloy. The kinetics and dynamics of the thermal processes of crystallization of AZ91 alloy in the ceramic shells were determined. Metallographic tests were performed with the use of an optical microscope. A comparison of these test results with the thermal effect recorded by way of the TDA method was made. Influence of cooling rate of AZ91 on HV0, 01 micro-hardness and Brinell hardness alloy was examined.
The purpose of the research was mapping, inventorization, and valorization of coal mining waste dumps from the mines of JSW SA company, for the needs of recovery of coal from the dump material as well as the reclamation and management of examined facilities. The valorization of post-mining waste dumps has been carried out using a methodology which considers the problems of reclamation, management, accessibility of the dumps as well as environmental hazards connected with disposing of mining and preparation wastes on the ground surface. An inventorization of 10 coal mining waste dumps coming from 6 mines of JSW SA including in their range 7 deposits: Borynia, Jastrzębie, Zofiówka, Budryk, Knurów, Szczygłowice and Pniówek was carried out. The source material within the localization of particular dumps was obtained from archival materials coming from coal mines and municipalities where the dumps are located. Verified data has been drawn on topographical map, which results in the map of coal mining waste dumps. The results of the valorization of the dumps comprise the defining of: the name of the dump, state of the dump, surface of the dump, accessibility, name of the coal mine from where the wastes come from, type of technical and biological reclamation and possibilities of coal recovery, which have been brought on the drawn map. Basing on collected and elaborated data, an attempt of defining of potential possibilities of recovery of coal from the dumps and connection of coal quality in the deposits of JSW SA and in waste material was made. The results of the research showed that in spite of preliminary information that a majority of the investigated dumps may be considered as potential facilities for coal recovery, ultimately the recovery is economically justified only in several cases (5 facilities).
The new legislative provisions, regulating the trade in solid fuels in our country, draw attention to the need to develop and improve methods and methods of managing hard coal sludge. The aim of the work was to show whether filtration parameters (mainly the permeability coefficient) of hard coal sludge are sufficient for construction of insulating layers in landfills at the stage of their closing and what is the demand for material in the case of such a procedure. The analysis was carried out for landfills for municipal waste in the Opolskie, Śląskie and Małopolskie provinces. For hard coal sludge, the permeability coefficient values are in the range of 10–8–10–11 m/s, with the average value of 3.16 × 10–9 m/s. It can be concluded that this material generally meets the criteria of tightness for horizontal and often vertical flows. When compaction, increasing load or mixing with fly ash from hard coal combustion and clays, the achieved permeability coefficient often lowers its values. Based on the analysis, it can be assumed that hard coal sludge can be used to build mineral insulating barriers. At the end of 2016, 50 municipal landfills were open in the Opolskie, Śląskie and Małopolskie Provinces. Only 36 of them have obtained the status of a regional installation, close to 1/3 of the municipal landfill are within the Major Groundwater Basin (MGB) range. The remaining storage sites will be designated for closure. Assuming the necessity to close all currently active municipal waste landfills, the demand for hard coal sludge amounts to a total of 1,779,000 m3 which, given the assumptions, gives a mass of 2,704,080 Mg. The total amount of hard coal sludge production is very high in Poland. Only two basic mining groups annually produce a total of about 1,500,000 Mg of coal sludge. The construction of insulating layers in landfills of inert, hazardous and non-hazardous and inert wastes is an interesting solution. Such an application is prospective, but it will not solve the problem related to the production and management of this waste material as a whole. It is important to look for further solutions.
The paper presents selected issues related to the development of international coal markets. World consumption of coal dropped for the second year in a row in 2016, primarily due to the lower demand from China and the US. The share of coal in global primary energy consumption decreased to 28%. World coal production accounted to 3.66 billion toe and it was lower by 6.2% when compared to the previous year. More than 60% of this decline took place in China. The decline in global production was more than four times higher than the decrease in consumption. The sufficiency of the world resources of coal are estimated at 153 years – that is three times more than the sufficiency of oil and gas resources. After several years of decline, coal prices increased by 77% in 2016. The current spot prices are at the level of $80/ton and are close to the 2014 prices. In the European market, after the first half of the year, coal prices reached the level of around 66% higher than in the same period of the last year. The average price in the first half amounted to PLN 12.6/GJ, which is close to the 2012 prices. The share of spot trade in the total purchase amount accounted to approx. 20%. Prices in futures contracts can be estimated on the basis of the Japan-Australia contracts prices and prices in supplies to power plants located in Germany. On average, the prices in supplies to these power plants were higher by approximately 9% in the years 2010 – 2016 and prices in Australia – Japan contracts were 12% higher than CIF ARA prices in 2017. Global energy coal trade reached about 1.012 billion tons in 2016. A decline by 4.8% is expected in 2019 primarily due to the expected reduction in demand in major importing countries in Asia.
Significant quantities of coal sludge are created during the coal enrichment processes in the mechanical processing plants of hard coal mines (waste group 01). These are the smallest grain classes with a grain size below 1 mm, in which the classes below 0.035 mm constitute up to 60% of their composition and the heat of combustion is at the level of 10 MJ/kg. The high moisture of coal sludge is characteristic, which after dewatering on filter presses reaches the value of 16–28% (Wtot r) (archival paper PG SILESIA). The fine-grained nature and high moisture of the material cause great difficulties at the stage of transport, loading and unloading of the material. The paper presents the results of pelletizing (granulating) grinding of coal sludge by itself and the piling of coal sludge with additional material, which is to improve the sludge energy properties. The piling process itself is primarily intended to improve transport possibilities. Initial tests have been undertaken to show changes in parameters by preparing coal sludge mixtures (PG SILESIA) with lignite coal dusts (LEAG). The process of piling sludge and their mixtures on an AGH laboratory vibratory grinder construction was carried out. As a result of the tests, it can be concluded that all mixtures are susceptible to granulation. This process undoubtedly broadens the transport possibilities of the material. The grain composition of the obtained material after granulation is satisfactory. Up to 2 to 20 mm granules make up 90–95% of the product weight. The strength of the fresh pellets is satisfactory and comparable for all mixtures. Fresh lumps subjected to a test for discharges from a height of 700 mm can withstand from 7 to 14 discharges. The strength of the pellets after longer seasoning, from the height of 500 mm, shows different values for the analyzed samples. The values obtained for hard coal sludge and their blends with brown coal dust are at the level from 4 to 5 discharges. The strength obtained is sufficient to determine the possibility of their transport. At this stage of the work it can be stated that the addition of coal dust from lignite does not cause the deterioration of the material’s strength with respect to clean coal sludge. Therefore, there is no negative impact on the transportability of the granulated material. As a result of mixing with coal dusts, it is possible to increase their energy value (Klojzy-Karczmarczyk at al. 2018). The cost analysis of the analyzed project was not carried out.
The article compares the management of energy resources in Poland and Ukraine over the period 2000–2017. The analysis took changes in the volume of coal, oil and natural gas resources into consideration. The indicators of supplies of these fuels for Poland and Ukraine have additionally been compared with selected EU countries. In order to assess energy security of Poland and Ukraine, the changes in the primary energy consumption have been analyzed in general in first order, then the possibilities of meeting the demand for natural gas, coal and oil have been determined based on the domestic extraction of individual energy resources. Such a comparison indicates the dominant role of coal in Poland while the extraction of oil and natural gas meets the domestic demand to a greater extent in Ukraine. Over the period 2000-2017, trends in primary energy consumption were different; a 17% increase was noted in Poland, while a nearly 40% decline was noted in Ukraine. The main factors responsible for radical changes in fuel and energy management in Ukraine have been identified: military operations in the east of the country and the annexation of Crimea, demographic changes. These events had a negative impact especially on the volume of hard coal mining in Ukraine; the significant increase in imports from 5.36 to 19.14 million tons in 2011-2017 was necessary for balancing. The balance of foreign exchange for electricity was also compared. Over the past years, this comparison has been favorable for Ukraine, where the dominance of electricity exports over imports is noticeable, which generated revenues of over USD 200 million in 2017.
Heat treatment of a casting elements poured from silumins belongs to technological processes aimed mainly at change of their mechanical properties in solid state, inducing predetermined structural changes, which are based on precipitation processes (structural strengthening of the material), being a derivative of temperature and duration of solutioning and ageing operations. The subject-matter of this paper is the issue concerning implementation of a heat treatment process, basing on selection of dispersion hardening parameters to assure improvement of technological quality in terms of mechanical properties of a clamping element of energy network suspension, poured from hypoeutectic silumin of the LM25 brand; performed on the basis of experimental research program with use of the ATD method, serving to determination of temperature range of solutioning and ageing treatments. The heat treatment performed in laboratory conditions on a component of energy network suspension has enabled increase of the tensile strength Rm and the hardness HB with about 60-70% comparing to the casting without the heat treatment, when the casting was solutioned at temperature 520 o C for 1 hour and aged at temperature 165 o C during 3 hours.
Al- and Al/Zn-enriched layers containing intermetallic phases were deposited on the Mg substrate by heating the Mg specimens in contact with the powdered materials in a vacuum furnace. The Al-enriched surface layers were produced using Al powder, whereas the Al/Znenriched layers were obtained from an 80 wt.% Al + 20 wt.% Zn powder mixture. The microstructure and composition of the layers were analyzed by optical microscopy, scanning electron microscopy and X-ray diffraction. The results showed that the Al-enriched layer comprised an Mg17Al12 intermetallic phase and a solid solution of Al in Mg. The layer obtained from the Al+Zn powder mixture was composed of Mg-Al-Zn intermetalic phases and a solid solution of Al and Zn in Mg. Adding 20% of Zn into the Al powder resulted in the formation of a considerably thicker layer. Moreover, the hardness of the surface layers was much higher than that of the Mg substrate.
The paper presents the results of studies to determine the effect of complex surface and bulk modification and double filtration during mould pouring on the stereological parameters of macrostructure and mechanical properties of castings made from the post-production waste IN-713C and the MAR-247 nickel alloys. The evaluation covered the number of grains per 1mm2 of the sample surface area, the average area of grains and the shape index, hardness HB, tensile strength and resistance to high temperature creep. The results indicate the possibility of controlling the stereological parameters of macrostructure through application of several variants of the modification, controlling in this way also different low- and high-temperature properties. The positive effect of double filtration of the alloy during mould pouring on the metallurgical quality and mechanical properties of castings has also been emphasized.
The paper presents the technology of manufacturing layered castings, consisting of grey cast iron (base part) and high-chromium stainless steel (working part/layer). The aim of researches was an attempt of integration of heat treatment of steel X46Cr13 grade with founding of grey cast iron in bimetallic system and determination of the influence of cooling rate of bimetallic system in classical sand mould with bentonite on microstructure and hardness of the working layer. The castings were manufactured using mould cavity preparation method, where steel plate was poured by grey cast iron using different pouring temperature and thickness of base part. Then, the quality of joint between cast iron and steel plate was estimated by using ultrasonic non-destructive testing. The efficiency of heat treatment process was analysed by measurement of hardness and in metallographic examination. Conducted studies showed, that self-hardening’s ability of steel X46Cr13 let obtain technologically usable layered casting characterized by hardness of working surface up to 35 HRC.
Welding strength is very important in safe use of polypropylene sheets. The determination of welding parameters and design of the welding tool has an impact on the weld strength. The welding parameters can be determined experimentally. In this study, Charpy impact test is used to determine suitable welding parameters in welding of polypropylene sheets with FSW method. At the same time, the weld zone microstructure is examined and Shore hardness measurements are made. The impact tests were performed on samples cut from the welded sheets. The impact tests values and hardness values were presented graphically. According to the test results, some welded parts behaved similar to the matrix material. In some welding parameters, Charpy impact test values were obtained close to values of the main materials. The suitable welding parameters were determined for polypropylene sheets welding.
The paper presents the capabilities of welding techniques to creating properties of wear resistant high chromium cast iron alloy. The use of the right kind of welding sequence allows you to change the structure and properties of the obtained welds. Tests were conducted for one type of additive material in the form of self shielded core wire. In order to determine the effect of the type of welding sequence on the properties of welds performed welding using string bead and weave bead. The resulting weld was tested on hardness and research structure in an optical microscope. In the following studies have been made erosive tests wear of made hardfacing. String beads gave structure rich in carbides and harder about 270 HV of the weld with weave bead. Also, wear resistance was nearly twice as better for welds made with string beads. In the experiment a decisive role in the resistance to wear plays a high hardness of the deposit and the presence of carbides in its structure. Changes in the basic parameters of the deposition process allows for the formation of structure and properties of hardfacing welds in a wide range.
Aluminium based metal matrix composite (Al-MMC’s) are much popular in the field like automobile and aerospace industries, because of its ease of fabrication process and excellent mechanical properties. In this study, Al-Zn-Mg alloy composite reinforced with 3, 6 and 9 v % of zircon sand was synthesised by stir casting technique. The microstructure of the composites revealed uniform distribution of reinforced particles. Hardness, tensile strength and wear resistance of Al-Zn-Mg alloy/zircon sand composite were found to increase with increase in v % percentage of zircon sand. Scanning Electron Microscope analysis of wear tested sample surface of composites revealed no evidence of plastic deformation of matrix phase. Particle pulls out and abrasive wear was the common feature observed from all the composites.
This paper focused on the effect of pure torsion deformation and various torsion pitches on the mechanical properties of the commercial pure Al wires which has not been examined so far. The initial wires with diameter of 4 mm have been torsion deformed to different pitch length (PL). In order to investigate the effect of gradient microstructure caused by torsion deformation, three different pitch length of 15 mm, 20 mm and 30 mm are considered. The results revealed that the level of grain refinement is correlated with the amount of induced plastic shear strain by torsion deformation. For the wire with pitch length of 15 mm, the grain sizes decreased to about 106 μm and 47 μm in the wire center and edge from the initial size of about 150 μm of the annealed wire. The micro-hardness measurement results show a gradient distribution of hardness from the wire center to the wire surface that confirmed the increasing trend of plastic shear strain obtained by FE simulations. The hardness of annealed sample (35 HV) is increased up to 73 HV at the wire surface for the smallest pitch length. The yield and ultimate tensile strength of the torsion deformed wires are also increased up to about 85 MPa and 152 MPa from the initial values of 38 MPa and 103 MPa of the annealed one respectively while the maximum elongation reduced significantly.
The paper presents results of Ti-addition to High Chromium Cast Iron (HCCI) on the structure and selected mechanical properties. For this study casted two sets of cylinders with dimensions ø20 mm, ø15 mm x 250 mm, for the High Chromium Cast Iron (HCCI) and with the 4% by mass Ti-addition. Melts were performed in the induction furnace crucible capacity of 15 kg. During the heats the cup with installed S type thermocouple was poured to record the cooling curves. The cylinders were subjected to the static bending strength test. Samples for the test microstructure and Rockwell hardness were cut from the cylinders. The study shows that the addition of titanium had an impact on the structure and thus the properties of High Chromium Cast Iron (HCCI). In subsequent studies, through an appropriate choice of chemical composition and proper process control, it is planned to obtain in the structure the titanium carbides TiC and chromium carbides with type (Cr, Fe)7C3.