This paper deals with the modelling of traction linear induction motors (LIMs) for public transportation. The magnetic end effect inherent to these motors causes an asymmetry of their phase impedances. Thus, if the LIM is supplied from the three-phase symmetrical voltage, its phase currents become asymmetric. This effect must be taken into consideration when simulating the LIMs’ performance. Otherwise, when the motor phase currents are assumed to be symmetric in the simulation, the simulation results are in error. This paper investigates the LIM performance, considering the end-effect induced asymmetry of the phase currents, and presents a comparative study of the LIM performance characteristics in both the voltage and the current mode.
The subject of the paper is the analysis of factors determining the value of multi-entity organizations in the energy sector and their ranking according to the degree of impact on this value. For this purpose, statistical methods were used, which are best suited to determine the order of diagnostic features according to a specific criterion. The survey covered companies from the Polish energy sector, while the process itself is based on aggregated data, which represents the financial data of capital groups currently operating in the Polish energy sector. The first part of the article presents a short description of the Polish energy sector, paying particular attention to the organizational structure of the sector, i.e. companies operating on the domestic energy market. The nature of a multi-entity enterprise as a typical economic unit in the sector is described. The second part of the article describes the assumptions of multidimensional comparative analysis (MCA) as a tool for comparing multifunctional units. The MCA makes it possible to find the most important parameters or indicators having the greatest impact on the value of a multi-entity organization, i.e. a capital group. The survey covered four companies from the Polish energy sector: TAURON Polska Energia SA, ENEA SA, ENERGA SA and PGE Polska Grupa Energetyczna SA. The study with the use of MCA was conducted in three stages: - in the first stage, on the basis of information contained in the financial statements, a matrix of diagnostic features was created, describing the financial condition of the examined entity, - in the second stage, the values of diagnostic variables were normalized/unified; two methods of normalization were applied: the method of standardization and zero unitization, - in the third stage, the diagnostic variables were grouped using two methods: the model measure of Hellwig’s development and the non-standard measure of development. The results of the analysis are illustrated by tables and figures.
The paper presents validation tests for method which is used for the evaluation of the statistical distribution parameters for 3D particles’ diameters. The tested method, as source data, uses chord sets which are registered from a random cutting plane placed inside a sample space. In the sample space, there were individually generated three sets containing 3D virtual spheres. Each set had different Cumulative Distribution Function (CDF3) of the sphere diameters, namely: constant radius, normal distribution and bimodal distribution as a superposition of two normal distributions. It has been shown that having only a chord set it is possible, by using the tested method, to calculate the mean value of the outer sphere areas. For the sets of data, a chord method generates quite large errors for around 10% of the smallest nodules in the analysed population. With the increase of the nodule radii, the estimation errors decrease. The tested method may be applied to foundry issues e.g. for the estimation of gas pore sizes in castings or for the estimation of nodule graphite sizes in ductile cast iron.
The determination of the form of a probability density function (PDF3) of diameters for nodular particles by using a probability density function (PDF2), which form is empirically estimated from cross-sections of these nodules in a metallographic specimen, can be regarded as a special case of Wicksell's corpuscle problem (WCP). The estimation of the PDF3 for the nodular particles provides information about the kinetics of these particles nucleation, and so about the kinetics of their growth. This information is essential for building more accurate mathematical models of the alloy crystallization. In the paper there are presented two derivations of the methods used for the estimation of the PDF3 form. The first method bases on diameters received from a planar cross-section. The second one uses also data from the planar cross-section but not the diameters only chords. Both methods provide practical rules for the analysis of the empirical diameters’ and chord’s size distribution and allow to estimate the mean value of the external surface area of the particles.
Steady-state characteristics of a catalytic fluidised bed reactor and its dynamical consequences are analyzed. The occurrence of an untypical steady-state structure manifesting in a form of multiple isolas is described. A two-phase bubbling bed model is used for a quantitative description of the bed of catalyst. The influence of heat exchange intensity and a fluidisation ratio onto the generation of isolated solution branches is presented for two kinetic schemes. Dynamical consequences of the coexistence of such untypical branches of steady states are presented. The impact of linear growth of the fluidisation ratio and step change of the cooling medium temperature onto the desired product yield is analyzed. The results presented in this study confirm that the identification of a region of the occurrence of multiple isolas is important due to their strong impact both on the process start-up and its control.
This article employs the classical Euler–Bernoulli beam theory in connection with Green–Naghdi’s generalized thermoelasticity theory without energy dissipation to investigate the vibrating microbeam. The microbeam is considered with linearly varying thickness and subjected to various boundary conditions. The heat and motion equations are obtained using the modified couple stress analysis in terms of deflection with only one material length-scale parameter to capture the size-dependent behavior. Various combinations of free, simply-supported, and clamped boundary conditions are presented. The effect of length-to-thickness ratio, as well as the influence of both couple stress parameter and thermoelastic coupling, are all discussed. Furthermore, the effect of reference temperature on the eigenfrequency is also investigated. The vibration frequencies indicate that the tapered microbeam modeled by modified couple stress analysis causes more responses than that modeled by classical continuum beam theory, even the thermoelastic coupled is taken into account.