An electric power steering system (EPS) is a new type of steering system developed after a mechanical hydraulic power system (MHPS) and electric-hydraulic power steering system (EHPS). In order to coordinate and solve the portability and sensitivity of the steering system optimally, taking an induction power steering system as the research object, the control algorithm of induction motor control under the EPS is studied in this paper. In order to eliminate the feed-forward performance degradation caused by the change of feed-forward parameters, an on-line identification algorithm of feed-forward parameters is proposed. It can improve the control performance of online identification among three feed-forward parameters in the T-axle motor, it improves on the robustness of feed-forward control performance, at the same time it also gives simulation and test results. This method can improve the control performance of the three feed-forward parameter online identification of the T-axis motor and improve the robustness of feed-forward control performance. At the same time, simulation and test results are given. The simulation results show that the algorithm can significantly improve the response speed and control accuracy of EPS system control.
The aim of this study is to design a control strategy for the angular rate (speed) of a DC motor by varying the terminal voltage. This paper describes various designs for the control of direct current (DC) motors. We derive a transfer function for the system and connect it to a controller as feedback, taking the applied voltage as the system input and the angular velocity as the output. Different strategies combining proportional, integral, and derivative controllers along with phase lag compensators and lead integral compensators are investigated alongside the linear quadratic regulator. For each controller transfer function, the step response, root locus, and Bode plot are analysed to ascertain the behaviour of the system, and the results are compared to identify the optimal strategy. It is found that the linear quadratic controller provides the best overall performance in terms of steady-state error, response time, and system stability. The purpose of the study that took place was to design the most appropriate controller for the steadiness of DC motors. Throughout this study, analytical means like tuning methods, loop control, and stability criteria were adopted. The reason for this was to suffice the preconditions and obligations. Furthermore, for the sake of verifying the legitimacy of the controller results, modelling by MATLAB and Simulink was practiced on every controller.
The Variable Frequency Drive (VFD) is used to control the speed of the pumpmotor to attain the desired flow rate and fluid level in a fluid system. An AC drive provides efficient flow control by varying the pump-motor speed. The comparison of energy requirements and costs in a system where a throttling device is used for flow control on a centrifugal pump with the power used when an variable frequency drive (VFD) is used to control the same flow, evidently shows potential savings. In this system, AC Motor Frequency drive and static pressure transmitter, turbine type flowmeter and Analog/Digital cards, micro-control unit and computer connection are designed specially to control flow rate, fluid flow type (turbulence or laminar) and water level at the different conditions with different PID parameters.
The aim of the paper is a steady-state inverse heat transfer problem for plate-fin and tube heat exchangers. The objective of the process control is to adjust the number of fan revolutions per minute so that the water temperature at the heat exchanger outlet is equal to a preset value. Two control techniques were developed. The first is based on the presented mathematical model of the heat exchanger while the second is a digital proportional-integral-derivative (PID) control. The first procedure is very stable. The digital PID controller becomes unstable if the water volumetric flow rate changes significantly. The developed techniques were implemented in digital control system of the water exit temperature in a plate fin and tube heat exchanger. The measured exit temperature of the water was very close to the set value of the temperature if the first method was used. The experiments showed that the PID controller works also well but becomes frequently unstable.
This paper presents a development of a model of a set of multistage centrifugal electro pumps including two 4 stage stainless steel centrifugal pumps, each coupled to a 4 kW three-phase induction motor, connected to a hydraulic application running under two control strategies including constant speed and variable speed methods. Each pump provides 16 m3/hr flow rate and 58mwaterhead at BEP (Best Efficiency Point). Dynamicity of the model causes variations in all operational parameters of pumping system in any variation on consuming flow rate. Each electro pump has been driven with a variable frequency drive utilizing frequency control method for adjusting the rotational speed under a PID control regarding to match of pumping system operational point with the consumption point to save the energy. 83% energy saving is achieved by model in variable speed control strategy comparing to constant speed control strategy. MATLAB/SIMULINK software using ode45 solver and variable step size simulates this model.
The proportional-integral-derivative (PID) controllers have experienced series of structural modifications and improvements. Example of such modifications are set-point weighting and fractional ordering. While the former is to achieve two-degree-of-freedom (2DOF) ability of set-point tracking and disturbance rejection, the latter is to ensure smooth control action. Therefore, this paper reviews various forms of PID controllers and provides a comparative analysis of 2DOF PID and 2DOF fractional order PID (FOPID) controllers. The paper also discusses the conversion of one PID form to another. For the comparative analysis of the various controllers, a class of unstable systems are considered. Simulation result shows that in most cases the conversion from one form to another does not significantly affect the performance of the system. It is also observed that the 2DOF controllers (2DOF PID and 2DOF FOPID) improved significantly the performance of the ordinary PID controllers.
Foundry resistance furnaces are thermal devices with a relatively large time delay in their response to a change in power parameters. Commonly used in automation classical PID controllers do not meet the requirements of high-quality control. Developed in recent years, fuzzy control theory is increasingly being used in various branches of economy and industry. Fuzzy controllers allow to introduce new developments in control systems of foundry furnaces as well. Correctly selected fuzzy controller can significantly reduce energy consumption in a controlled thermal process of heating equipment. The article presents a comparison of energy consumption by control system of foundry resistance furnace, equipped with either a PID controller or fuzzy controller optimally chosen.