Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 8
items per page: 25 50 75
Sort by:

Abstract

The paper presents the adaptation of the modified pulse method for investigating temperature characteristics of thermal diffusivity in the vicinity of the second-order phase transition points. The principle of the adaptation consists in the modified in relation to the original method, development of the characteristics of temperature changes between boundary surfaces of a flat-parallel specimen after the laser shot onto its front surface. The application of this adaptation was illustrated with investigation into thermal diffusivity of nickel (99.9% wt) in the temperature range of 20-380◦C. In all cases the measurement error was less than 3%, and the averaging interval for the measured values of thermal diffusivity was not greater than 1.2 K.
Go to article

Abstract

The presence of more than one solute diffused in fluid mixtures is very often requested for discussing the natural phenomena such as transportation of contaminants, underground water, acid rain and so on. In the paper, the effect of nonlinear thermal radiation on triple diffusive convective boundary layer flow of Casson nanofluid along a horizontal plate is theoretically investigated. Similarity transformations are utilized to reduce the governing partial differential equations into a set of nonlinear ordinary differential equations. The reduced equations are numerically solved using Runge-Kutta-Fehlberg fourth-fifth order method along with shooting technique. The impact of several existing physical parameters on velocity, temperature, solutal and nanofluid concentration profiles are analyzed through graphs and tables in detail. It is found that, modified Dufour parameter and Dufour solutal Lewis number enhances the temperature and solutal concentration profiles respectively.
Go to article

Abstract

The Low Temperature Joining Technique (LTJT) using silver compounds enables to significantly increase the thermal conductivity between joined elements, which is much higher than for soldered joints. However, it also makes difficult to measure the thermal conductivity of the joint. The Laser Flash Analysis (LFA) is a non-intrusive method of measuring the temperature rise of one surface of a specimen after excitation with a laser pulse of its other surface. The main limitation of the LFA method is its standard computer software, which assumes the dimensions of a bonded component to be similar to those of the substrate, because it uses the standard Parker’s formula dedicated for one-dimensional heat flow. In the paper a special design of measured specimen was proposed, consisting of two copper plates of different size joined with the sintered silver layer. It was shown that heat properties of these specimens can also be measured after modifying the LFA method. The authors adapted these specimens by masking the false heat signal sourced from the uncovered plate area. Another adaptation was introducing a correcting factor of the heat travel distance, which was calculated with heat-flow simulations and placed into the Parker’s formula. The heat-flow simulated data were compared with the real LFA measurement results, which enabled estimation of the joint properties, e.g. its porosity.
Go to article

Abstract

In this study, a new laser flash system was proposed for the determination of the thermal conductivity of brown coal, hard coal and anthracite. The main objective of the investigation was to determine the effect of coal rank, composition, physical structure and temperature on thermal conductivity. The solid fuels tested were medium conductors of heat whose determined thermal conductivities were in the range of 0.09 to 0.23 W/(m K) at room temperature. The thermal conductivity of the solid fuels tested typically increased with the rank of coal and the measurement temperature. The results of this study show that the physical structure of solid fuels and temperature have a dominant effect on the fuels' thermal conductivity.
Go to article

Abstract

The paper presents the application of similarity theory to investigations of transient heat transfer in materials with complex structure. It describes the theoretical-experimental method for identification and design of the structure of two-component composite walls based on the research of the thermal diffusivity for the composite and its matrix separately. The thermal diffusivity was measured by means of the modified flash method. The method was tested on two samples of double-layer ‘epoxy resin – polyamide’. All the investigated samples had the same diameter of 12 mm and thickness ranging from 1.39–2.60 mm and their equivalent value of thermal diffusivity ranging from (1.21–1.98)×10-7m2/s. Testing the method and research on carbon/epoxy composites was carried out at temperatures close to room temperature.
Go to article

Abstract

A novel method for thermal diffusivity evolution of thin-film materials with pulsed Gaussian beam and infrared video is reported. Compared with common pulse methods performed in specialized labs, the proposed method implements a rapid on-line measurement without producing the off-centre detection error. Through mathematical deduction of the original heat conduction model, it is discovered that the area s, which is encircled by the maximum temperature curve rTMAX(θ), increases linearly over elapsed time. The thermal diffusivity is acquired from the growth rate of the area s. In this study, the off-centre detection error is avoided by performing the distance regularized level set evolution formulation. The area s was extracted from the binary images of temperature variation rate, without inducing errors from determination of the heat source centre. Thermal diffusivities of three materials, 304 stainless steel, titanium, and zirconium have been measured with the established on-line detection system, and the measurement errors are: −2.26%, −1.07%, and 1.61% respectively.
Go to article

Abstract

Transient heat transfer is studied and compared in two plane-parallel composite walls and one EPIDIAN 53 epoxy resin wall acting as a matrix for both composites. The first of the two walls is made of carbon-epoxy composite; the other wall is made of glass-epoxy composite, both with comparable thickness of about 1 mm and the same number of carbon and glass fabric layers (four layers). The study was conducted for temperatures in the range of 20-120 °C. The results of the study of thermal diffusivity which characterizes the material as a heat conductor under transient conditions have a preliminary character. Three series of tests were conducted for each wall. Each series took about 24 h. The results from the three series were approximated using linear functions and were found between (0.7-1.35) x 10-7m2/s. In the whole range of temperature variation, the thermal diffusivity values for carbon-epoxy composite are from 1.2 to 1.5 times higher than those for the other two materials with nearly the same thermal diffusivity characteristics.
Go to article

Abstract

Results of the ab initio molecular dynamics calculations of silicon crystals are presented by means of analysis of the velocity autocorrelation function and determination of mean phonon relaxation time. The mean phonon relaxation time is crucial for prediction of the phonon-associated coefficient of thermal conductivity of materials. A clear correlation between the velocity autocorrelation function relaxation time and the coefficient of thermal diffusivity has been found. The analysis of the results obtained has indicated a decrease of the velocity autocorrelation function relaxation time t with increase of temperature. The method proposed may be used to estimate the coefficient of ther-mal diffusivity and thermal conductivity of the materials based on silicon and of other wide-bandgap semiconductors. The correlation between kinetic energy fluctuations and relaxation time of the velocity autocorrelation function has been calculated with the relatively high coefficient of determination R2 = 0.9396. The correlation obtained and the corresponding approach substantiate the use of kinetic energy fluctuations for the calculation of values related to heat conductivity in silicon-based semiconductors (coefficients of thermal conductivity and diffusivity).
Go to article

This page uses 'cookies'. Learn more