The investigation results of the mechanical reclamation of spent moulding sands from the Cordis technology are presented in the paper. The quality assessment of the obtained reclaim and the influence of the reclaim fraction in a matrix on the core sand strength is given. The reclaim quality assessment was performed on the basis of the determination of losses on ignition, Na2O content on reclaim grains and pH values. The reclaim constituted 100%, 75% and 50% of the core sand matrix, for which the bending strength was determined. The matrix reclamation treatment was performed in the experimental rotor reclaimer RD-6. Spent sands were applied in as-delivered condition and after the heating to a temperature of 140 o C. Shaped samples for strength tests were made by shooting and hardening of sands in the warmbox technology.
The results of investigations of sand shooting into the core box are presented in the hereby paper. The investigations concern the formation of the diphase sand-air flux, its motion, flowing and compaction in the cavity during the core forming. Conditions deciding on the course of individual phases of the process are discussed with taking into consideration the influence of such factors as: the shot pressure, shooting hole diameter, number and distribution of deaerating vents in experimental core boxes (of a single cavity and of multi cavities) on the core sand compaction state. Investigations were performed by means of the modernised experimental shooting machine SR-3D, of the shooting chamber volume of 3.3 dm3, connected with the system of pneumatic supply ensuring the stable pressure supply of values: 0.4 MPa, 0.5 MPa and 0.6 MPa. Two diameters of the shooting hole, equal 10 mm and 20 mm, were applied for filling three experimental core boxes differing in dimensions of cavities and in number and distribution of deaerating vents. The filling process of core boxes was recorded by means of the digital camera PHANTOM V210 with the filming rate of 3000 pictures in second. Simultaneously, during the shot, other values allowing to determine the intensity of the core sand outflow from the shooting chamber to the core box, were tested. The presented in this publication results constitute the important element of the experimental verification of the blowing process simulation calculations which will be performed.
Core sands for blowing processes, belong to these sands in which small amount of the applied binding material has the ability of covering the sand matrix surface in a way which - at relatively small coating thickness - allows to achieve the high strength. Although the deciding factor constitute, in this aspect, strength properties of a binder, its viscosity and ability to moisten the matrix surface, the essential meaning for the strength properties of the prepared moulding sand and the mould has the packing method of differing in sizes sand grains with the coating of the binding material deposited on their surfaces. The knowledge of the influence of the compaction degree of grains forming the core on the total contact surface area can be the essential information concerning the core strength. Forecasting the strength properties of core sands, at known properties of the applied chemically hardened binder and the quartz matrix, requires certain modifications of the existing theoretical models. They should be made more realistic with regard to assumptions concerning grain sizes composition of quartz sands and the packing structure deciding on the active surface area of the contacts between grains of various sizes and - in consequence - on the final strength of cores.
The results of model investigations of the influence of the blowing process selected parameters on the distribution of the compaction of the core made by the blowing method, are presented in the hereby paper. These parameters were: shooting pressure, shooting hole diameter, amount and distribution of deaerating holes. Investigations were performed using the horizontal core box of the cuboidal cavity and the same core box into which inner inserts were introduced. These inserts were dividing the primary volume into three sectors differing in their direction, introduction conditions and the character of the core sand flow. As the compaction measure the apparent sand density was assumed. The density was determined in five measuring points in case of uniform cores, and in three measuring points in case of cores obtained in the core box with three separated sectors. The apparent density of the compacted core sand in the core box cavity was determined on the basis of the measurements of masses and volumes of samples cut-out from the determined core places by means of the measuring probe. Investigations were performed at three values of the working pressure equal 0.4, 0.5 and 0.6MPa for two diameters of the shooting hole: 10 and 20 mm. During tests the core box deaeration, controlled by an activisation of the determined number of deaerating vents placed in the core box, was also subjected to changes.
The results of investigations of the influence of the matrix grain sizes on properties of cores made by the blowing method are presented in the hereby paper. Five kinds of matrices, differing in grain size compositions, determined by the laser diffraction method in the Analysette 22NanoTec device, were applied in investigations. Individual kinds of matrices were used for making core sands in the Cordis technology. From these sands the shaped elements, for determining the apparent density of compacted sands and their bending strength, were made by the blowing method. The shaped elements (cores) were made at shooting pressures being 3, 4 and 5 atn. The bending strength of samples were determined directly after their preparation and after the storing time of 1 hour.
The paper presents the results of analyzes of gases emitted during exposure to high temperature foundry molding sands, where binders are organic resins. As a research tool has been used special gas chromatograph designed to identify odorous compounds including the group of alkanes.
The use of environmentally friendly inorganic binders and new technologies for cores production is widely discussed topic in recent years. This paper contains information about new hot curing process for core making with alumina-silicate based inorganic binders – geopolymers. Main differences between hot cured geopolymers and hot cured alkali silicate based inorganic binders are discussed. The main objective of this research paper was to investigate basic technological properties of geopolymer binder system such as strength, compaction, storage ability and knock-out properties. For this purpose, three mixtures with different powder additives were prepared and tested in laboratory conditions using specific methods. Strength properties evaluation showed sufficient levels as well as knock-out properties measurement, even with additives B and C originally designed for the use with alkali silicate based two component binder systems. Additives B and C were considered compatible with geopolymer binders after casting production trial results. Storage ability of geopolymers seems to be more sensitive than of alkali silicate based binders in the same tested conditions. Mixtures with geopolymer binder showed 20% more decrease of strength compared to alkali silicate binders after 24 hours in conditions of 25 °C and 65 %RH.
Skeleton castings macrostructure can be shaped in many ways, by choosing an appropriate material of cores and manufacturing technologies. Important factor, which puts foundry techniques over the other technologies of periodic cellular materials, is ability to adjust mechanical properties by changing the microstructure of an alloy from which the casting is made. The influence on the microstructure of the skeleton casting can be implemented by choosing the thermal properties, mainly thermal conductivity factor, of mould and core materials. Macro- and microstructure of skeleton castings with octahedron elementary cells was presented in this paper. The analysis concerns the differences in morphology of eutectic silicone depending on the location of measurements cross sections areas. The use of thermo-insulating material with appropriate properties assures correct fill of mould cavity and homogeneous microstructure on whole volume of skeleton casting. The selection of technological parameters of the casting process if very important as well.