Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 11
items per page: 25 50 75
Sort by:

Abstract

During drilling through aquifers using the rotary drilling method with drilling fluid application, the phenomenon of formation clogging in near-well zone takes place. This leads to physical changes in pore spaces in consequence of the deposition solid phase particles originating from the drilling fluid. Due to this fact, filtration velocity in the clogged zones of the aquifer formation decreases, which results in increased pressure drawdown and decreased well hydraulic efficiency. Therefore, it causes a reduction of the well total capacity. The article consists of studies connected to the development of the mud which will constitute the basis for a complex mud system intended for hydrogeological drilling in different encountered geological conditions. In the framework of laboratory research, technological parameters of six, commonly applied in oil and gas industry, polymer agents as well as new agent developed at the Drilling, Oil and Gas Faculty AGH-UST in Krakow were examined. The undertaken studies showed that the new agent, marked as CAGEx, provides the required technological parameters and can be applied as a base for drilling muds intended for hydrogeological drilling. The undertaken industrial research of the new CAGEx drilling mud carried out while drilling water intake well, confirmed the great stability of its technological parameters as well as insignificant influence on rock permeability damage in filter zone. The water intake well is characterized by high hydraulic efficiency and does not require additional activation treatment.
Go to article

Abstract

In the last decade, Poland has become one of the most active markets for unconventional hydrocarbon deposits exploration. At present, there are twenty concessions for the exploration and/or discovery of reserves, including shale gas. The area covered by exploration concessions constitutes ca. 7.5% of the country’s area. Four main stages can be distinguished In the shale gas development and exploitation project: the selection and preparation of the place of development of the wells, hydraulic drilling and fracturing, exploitation (production) and marketing, exploitation suppression and land reclamation. In the paper, the concept of cost analysis of an investment project related to the exploration and development of a shale gas field/area was presented. The first two stages related to the preparatory work, carried out on the selected site, as well as drilling and hydraulic fracturing were analyzed. For economic reasons, the only rational way to make shale gas reserves available is to use horizontal drilling, either singly or in groups. The number of drilling pads covering the concession area is a fundamental determinant of the development cost of the deposit. In the paper, the results of the cost analysis of various types of reaming method with an area of 25,000,000 m2 were presented. Cost estimates were prepared for two variants: group drilling for three types of drilling pads: with three, five and seven wells and for single wells. The results show that, as the number of horizontal wells increases, the total cost of the development of the deposit is reduced. For tree-wells pad, these costs are 7% lower than in the second variant, for five-well pads they are 11% lower, and for seven-well pads they are 11.5% smaller than in the second variant. Authors, using applied methodology, indicate the direction of further research that will enable the optimization of shale gas drilling operations.
Go to article

Abstract

Hot point drills were carried through in the Hans Glacier (Spitsbergen). For that purpose a non-cored hot point drill of 700 wattage was constructed. It was used among others for installing the ablation-movement stakes, for hydrological observations and in the boreholes an ice temperature was controlled.
Go to article

Abstract

Plastic rocks can creep, therefore the knowledge of the rheological properties of the drilled formations is an important element of the drilling process and when choosing borehole designs. These properties of plastic formations also influence the way in which appropriate drilling technology and drilling mud properties are selected. The article presents the effect of basic rheological parameters of salt from the Fore-Sudetic Monocline deposit on the drilling of boreholes in the mining area of KGHM Polska Miedź, which in the future can be used as a good drilling practice to improve the safety and efficiency of drilling. The process of drilling in plastic rocks may be hindered. Salt is a plastic rock and in the analyzed rock mass it is deposited at a considerable depth. The caprock exerts big loads on it, beside the temperature in the deposit intensifies the rheological properties of the rock. The creep process causes that the borehole contracts, therefore the knowledge about the rheological properties of the drilled rock is very important for establishing the safe time in which the well may remain uncased. The paper is devoted to the influence of basic rheological parameters of salt bed in the Fore-Sudetic Monocline on the process of drilling of a borehole in the area of KGHM Polska Miedź as these data can be used in drilling practice in the future.
Go to article

Abstract

This work presents the methodology for analyzing the impact of ground vibrations induced during the drilling of gas/oil exploration wells on the surrounding constructions, as well as on humans and the natural environment. In the primary stage, this methodology is based on measurements of ground vibrations induced by a specific type of drilling system in the so-called reference site. In the next stage, ground vibrations are estimated in similar conditions to another design site, these conditions are assumed for a given drilling system, treated as a vibration source. In both sites, special seismic and geotechnical data are collected to construct numerical models for dynamic analyses. Finally, if it is required, a protection system is proposed with respect to the drilling technology and local conditions. The methodology presented has been tested on the terrain of an active natural gas mine used as the design site, and located in the southeastern part of Poland. The reference site was placed in the terrain of a working drilling system in similar conditions in the central part of Poland. Based on the results of numerical simulations, one may verify the different locations of the drilling rig in the design site with respect to the existing industrial structure. Due to the hazard from destructive ground vibrations, a certain vibroisolation system was proposed at the design site. Based on the results of numerical simulations one could rearrange the components of the drilling system in order to provide maximum security for the surrounding structures.
Go to article

[?]

Abstract

Drilling operations of the Cape Roberts Project took place between 1997 and 1999 offshore of Cape Roberts in the western Ross Sea, Antarctica. These were made possible due to a group effort by geoscientists from Australia, Germany, Italy, New Zealand, Great Britain, and the United States. The major goal of this undertaking was the recovery and analysis of sediment core, which was expected to provide a first East Antarctic record of the Early Cenozoic hothouse to icehouse climatic transition. This goal was not attained. Nevertheless, over the three seasons, a 1500 m long composite section was recovered, including a predominantly Early Oligocene to Early Miocene (34—17 Ma) glaciomarine succession. It was analyzed in terms of sediment physical properties, paleontology, tectonic structures and geophysics. This multidisciplinary investigation allowed detailed reconstruction of a significant portion of local environmental history, spanning a period of highly variable environmental conditions strongly affected by local glacier advance and retreat across the Victoria Land Basin margin.
Go to article

Abstract

Petroleum products are complex mixture of compounds of varied biological properties. They can cause harmful changes in contaminated ecosystems and threaten humans and living organisms as well. Bioremediation (including bioremediation stimulated by biogenic substances and inoculation with biopreparations from autochthonous bacteria and fungi) can result in creation of metabolites of a varied structure and biological activeness, which has been partly recognised. Some of them are more toxic than an initial substrate. Besides, they might have mutagenic features and be responsible for cancer. Estimation of bioremediation effectiveness in waste pits was completed with toxicological monitoring. It was led with the use of living organisms as biomarkers representing all trophic levels of a chosen ecosystem: producers, consumers and reducers. This process enables total estimation of natural environment conditions. The aim of the research was to determine the influence of petroleum contaminants and indirect metabolites (produced during bioremediation) on soil biocenose. The results of biotests (toxicity, phytotoxicity and genotoxity) have been taken into account. The following biotests, prepared and produced by Microbiotest, have been applied: PhytotoxkitTM, Ostracodtoxkit FTM, acute toxicity tests Microtox® Solid Phase and Ames mutagenicity tests. The obtained results enabled observation of changes in toxic properties during purification of the soil taken from waste pits. In addition, it can be claimed whether the areas are suitable for forest usage.
Go to article

Abstract

The condition monitoring techniques like acoustic emission, vibration analysis, and infrared thermography, used for the failure diagnosis of bearings, require longer processing time, as they have to perform acoustical measurement followed by signal processing and further analysis using special software. However, for any bearing, its period of usage can be easily determined within an hour, by measuring the bearing sound, using sound level meter (SLM). In this paper the acoustical analysis of the spindle bearing of a radial drilling machine was performed using SLM, by measuring the sound pressure level of the bearing in decibels, for different frequencies, while muting all the other noises. Then using an experimental set up, two database readings were taken, one for new bearing and the other for completely damaged bearing, both are SKF6207, which itself is the spindle bearing. From these three sets of sound pressure level readings, the period of usage of the spindle bearing, was calculated using an interpolation equation, by substituting the life of the bearing from the manufacturer’s catalogue. Therefore, for any machine with a SKF6207 bearing, its usage time can be estimated using the database readings and one measurement on that machine, all with the same speed.
Go to article

This page uses 'cookies'. Learn more