The need to modify conventional pavement rises due to high maintenance cost of the highway systems. With the continuously increased consumption, a large amount of waste glass materials is generated annually in the world. This paper aims to study the performance of pavement asphalt in which a fractional aggregate is replaced with crushed glass. In this paper, some important properties of asphalt mix, including stability, flow, specific gravity and air voids are investigated. The original sample is prepared without adding glass for different percentages of bitumen. Other samples are prepared by adding crushed glass to the mix with 5%, 10%, and 15% by aggregate weight. The results show that the properties of glass-asphalt mixture are improved in comparison with normal asphalt pavement. lt is concluded that the use of waste glass in asphalt pavement is desirable.
In the design of asphalt mixtures for paving, the choice of components has a remarkable importance,as requirements of quality and durability must be assured in use, guaranteeing adequate standardsof safety and comfort. In this paper, an approach of analysis on the aggregate materials using fractal geometry is proposed. Following an analytical and an experimental approach, it was possible to find a correlation betweencharacteristics of the asphalt concrete (specific gravity and porosity) and the fractal dimension ofthe aggregate mixtures. The studies revealed that this approach allows to draw the optimal fractal dimension and, conse-quently, it can be used to choose an appropriate aggregate gradation for the specific application;once the appropriate initial physical parameters are finalized. This fractal approach could be employed for predicting the porosity of mixed asphalt concretes,given as input the fractal characteristics of the aggregate mixtures of the concrete materials.
The aim of the study is to compare flexible pavement design lifespans and the main factors which create their values for a standard structure and one with an anti-fatigue course AF at different parameter values of pavement and its load, relevant to their design processes. Depending on the mixture used for the anti-fatigue course or the course thickness, durability improvement of the pavement (compared to the durability of a standard structure) can be obtained by extending the design lifespan of the asphalt base course or by extending the design lifespan of the AF course. On sections with predominantly slow traffic, the lifespan decreases significantly compared to sections with typical vehicle speed – the relative decrease is greater if anti-fatigue course is applied.
Traffic related noise is currently considered as an environmental pollution. Paper presents results of multidirectional study attempting to serve urban traffic without the need to erect noise barriers interfering urban space. Initial concept of the road expansion included construction of 1000 m of noise barriers dividing city space. Improvement in the acoustic conditions after construction completion is possible due to the applied noise protection measures: vehicle speed limit, smooth of traffic flow, use of road pavement of reduced noise emission and the technical improvement of the tramway.
The paper presents a numerical study of an aircraft wheel impacting on a flexible landing surface. The proposed 3D model simulates the behaviour of flexible runway pavement during the landing phase. This model was implemented in a finite element code in order to investigate the impact of repeated cycles of loads on pavement response. In the model, a multi-layer pavement structure was considered. In addition, the asphalt layer (HMA) was assumed to follow a viscoelastoplastic behaviour. The results demonstrate the capability of the model in predicting the permanent deformation distribution in the asphalt layer.
Communication noise is classified as one of the pollutions for the current environment. Experimental techniques to measure tire-pavement noise generation from asphalt pavements in the laboratory have been limited. A series of experiments were conducted on six different asphalt mixtures to determine if Purdue University’s Tire-Pavement Test Apparatus (TPTA) could be used to overcome these limitations. The procedure produced samples with low tire-pavement noise; however, the air void contents of the samples were higher than designed. Despite these difficulties, the sample preparation technique and the TPTA testing protocol were shown to offer an effective approach for quick laboratory assessment of tire-pavement noise characteristics of hot mix asphalt pavements at a substantially reduced cost compared to field testing.
The article presents numerical analysis of the portion of concrete airport pavement that consists of two concrete panels connected with dowels, subjected to thermal and service loads, in terms of changes in base rigidity, plate thickness and diameters, and spacing of dowels. Modifications of the thickness of the plates, diameter and spacing of dowels, and base rigidity were considered by assessing the level of stress and displacement in the analysed concrete plate, as well as normal and tangential stresses in dowels by using finite element method. On the basis of an analysis of examples, an optimal solution of dowelling connections in concrete plates with established loads was proposed. The results of the calculations were presented as a contour level distributions and comparison tables.
The paper analyses the influence of seasonal temperature variations on fatigue strength of flexible and semi-rigid pavement structures chosen for KR4 traffic flow category. The durability of pavement determined assuming a yearly equivalent temperature of 10˚C and assuming season-dependent equivalent temperatures was compared. Durability of pavement was determined with the use of Asphalt Institute Method and French Method. Finite Element Method was applied in order to obtain the strain and stress states by the means of ANSYS Mechanical software. Obtained results indicate a considerable drop in pavement durability if seasonal temperature variations are considered (up to 64% for flexible pavements and up to 80% for semi-rigid pavements). Durability obtained by the French Method presents lower dependence on the analysed aspect.
In the flexible road pavement design a mechanistic model of a multilayered half-space with linear elastic or viscoelastic layers is usually used for the pavement analysis. This paper describes a domain selection for the purpose of a FE model creating of the linear elastic layered half-space and boundary conditions on borders of that domain. This FE model should guarantee that the key components of displacements, stresses and strains obtained using ABAQUS program would be in particular identical with those ones obtained by analytical method using VEROAD program. It to achieve matching results with both methods is relatively easy for stresses and strains. However, for displacements, using FEM to obtain correct results is (understandably) highly problematic due to infinity of half-space. This paper proposes an original method of overcoming these difficulties.