Hallmark professionalism in probabilistic analysis is to quantify the uncertainties involved in construction materials subject to intrinsic randomness in its physical and mechanical properties and is now gaining popularity in civil engineering arena. As well, knowledge of behaviour of materials is continuously evolving and its statistical descriptors are also changing when more and more data collected or even data updated and hence reliability analysis has to be carried out with the updated data as a continuous process. As per the committee report ACI 544.2R, it is found that there is no attempt made for probabilistic relation between cube compressive strength and cylinder compressive strength for fiber reinforced concrete. In consequence of this report, a robust relation between cube and cylinder of experimentally conducted compressive strength was established by Monte-Carlo simulation technique for different types of fibrous concrete like steel, alkali resistant glass and polyester fibrous concrete before and after thermoshock considering various uncertainties. Nevertheless simulated probabilistic modals, characteristic modals, optimized factor of safety and allowable designed cylinder compressive strength have been developed from the drawn probability of failure graph, which exhibits robust performance in realistic Civil Engineering materials and structures.
In this paper, the applications of the multivariate data analysis and optimization on vibration signals from compressors have been tested on the assembly line to identify nonconforming products. The multivariate analysis has wide applicability in the optimization of weather forecasting, agricultural experiments, or, as in this case study, in quality control. The techniques of discriminant analysis and linear program were used to solve the problem. The acceleration and velocity signals used in this work were measured in twenty-five rotating compressors, of which eleven were classified as good baseline compressors and fourteen with manufacturing defects by the specialists in the final acoustic test of the production line. The results obtained with the discriminant analysis separated the conforming and nonconforming groups with a significance level of 0.01, which validated the proposed methodology.
The uncontrolled power flow in the AC power system caused by renewable energy sources (restless sources, distributed energy sources), dynamic loads, etc., is one of many causes of voltage perturbation, along with others, such as switching effects, faults, and adverse weather conditions. This paper presents a three-phase voltage and power flow controller, based on direct PWM AC/AC converters. The proposed solution is intended to protect sensitive loads against voltage fluctuation and problems with power flow control in an AC power system. In comparison to other solutions, such as DVR, UPFC, the presented solution is based on bipolar matrix choppers and operates without a DC energy storage unit or DC link. The proposed solution is able to compensate 50% voltage sags, in the case of three-phase symmetrical voltage perturbation, and single phase voltage interruptions. Additionally, by means of a voltage phase control with a range of #6;60◦ in each phase, it is possible to control the power flow in an AC power system. The paper presents an operational description, a theoretical analysis based on the averaged state space method and four terminal descriptions, and the experimental test results from a 1 kVA laboratory model operating under active load.
During operation, construction machines generate high noise levels which can adversely affect the health and the job performance of operators. The noise control techniques currently applied to reduce the noise transmitted into the operator cab are all based on the decrease of the sound pressure level. Merely reducing this noise parameter may be suitable for the compliance with the legislative requirements but, unfortunately, it is not sufficient to improve the subjective human response to noise. The absolute necessity to guarantee comfortable and safe conditions for workers, requires a change of perspective and the identification of different noise control criteria able to combine the reduction of noise levels with that of psychophysical descriptors representing those noise attributes related to the subjective acoustical discomfort. This paper presents the results of a study concerning the “customization” of a methodology based on Sound Quality for the noise control of construction machines. The purpose is to define new hearing-related criteria for the noise control able to guarantee not only reduced noise levels at the operator position but also a reduced annoyance perception.
The considered shunt active power filter can be controlled not only to compensate non-active current in the supply source, but additionally to optimize energy flow between the source and the load. In such a case the filter shapes the source current to be active and simultaneously regulates its magnitude. The presented filter/buffer can operate properly even when the load contains AC or DC variable energy source of any characteristic. The device can optimize energy flow for a single load, but also for a group of loads as well. The distinctive feature of the employed control method of the filter/buffer is that certain changes of energy stored in the device are utilized as the source of information concerning the active current of the load. This control method is very flexible and can be implemented to nearly all structures of active filters, for DC, single- and multiphase circuits.
Statistical Process Control (SPC) based on the well known Shewhart control charts, is widely used in contemporary manufacturing industry, including many foundries. However, the classic SPC methods require that the measured quantities, e.g. process or product parameters, are not auto-correlated, i.e. their current values do not depend on the preceding ones. For the processes which do not obey this assumption the Special Cause Control (SCC) charts were proposed, utilizing the residual data obtained from the time-series analysis. In the present paper the results of application of SCC charts to a green sand processing system are presented. The tests, made on real industrial data collected in a big iron foundry, were aimed at the comparison of occurrences of out-of-control signals detected in the original data with those appeared in the residual data. It was found that application of the SCC charts reduces numbers of the signals in almost all cases It is concluded that it can be helpful in avoiding false signals, i.e. resulting from predictable factors.
The paper presents preliminary results of investigations on a relationship between turbidity and other quality parameters in the SBR plant effluent. The laboratory tests demonstrated a high correlation between an effluent turbidity and a total suspended solids (TSS) concentration as well as between TSS and COD. Such a relationship would help to continuously monitor and control quality of a wastewater discharge using turbidity measurement.
Achieving control of coating thickness in foundry moulds is needed in order to guarantee uniform properties of the mould but also to achieve control of drying time. Since drying time of water based coatings is heavily dependent on the amount of water present in the coating layer, a stable coating process is prerequisite for a stable drying process. In this study, we analyse the effect of different variables on the coating layer properties. We start by considering four critical variables identified in a previous study such as sand compaction, coating density, dipping time and gravity and then we add centre points to the original experimental plans to identify possible non-linear effects and variation in process stability. Finally, we investigate the relation between coating penetration (a variable that is relatively simple to measure in production) and other coating layer thickness properties (relevant for the drying process design). Correlations are found and equations are provided. In particular it is found that water thickness can be directly correlated to penetration with a simple linear equation and without the need to account for other variables.