Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 199
items per page: 25 50 75
Sort by:

Abstract

This paper identifies the adverse events occurring during the execution of water supply and sewerage systems construction. The basis for this paper is research conducted in 2010-2014 on the construction sites of water supply and sewerage systems located in the provinces of Lower Silesia and Opole. The research consisted of direct observations of construction sites and review of construction documentation. It showed that work stoppages on the examined construction sites were frequent. They were caused by violations of work discipline by the production employees, adverse weather conditions, and defects in the project documentation. The study demonstrated that in almost every case, these bad an adverse effect on the completion date and budget of the investment. The analyses show that in such important and expensive investments as water supply and sewerage systems, organizational structures in which a special role is assigned to middle-rank personnel should be adopted.
Go to article

Abstract

This paper presents the design of digital controller for longitudinal aircraft model based on the Dynamic Contraction Method. The control task is formulated as a tracking problem of velocity and flight path angle, where decoupled output transients are accomplished in spite of incomplete information about varying parameters of the system and external disturbances. The design of digital controller based on the pseudo-continuous approach is presented, where the digital controller is the result of continuous-time controller discretization. A resulting output feedback controller has a simple form of a combination of low-order linear dynamical systems and a matrix whose entries depend nonlinearly on certain known process variables. Simulation results for an aircraft model confirm theoretical expectations.
Go to article

Abstract

The level of sales of a given good depends largely on the distribution network. An analysis of the distribution network allows companies to optimize business activity, which improves the efficiency and profitability of a company’s sales with an immediate effect on profit growth. The so-called spatial analysis is highly useful in this regard. The paper presents an analysis of the network of authorized dealers of the Polish Mining Group for the Opolskie Province. The analysis was done using GIS (SIP) tools. The purpose of the analysis was to present tools that could be used to verify an existing distribution network, to optimize it, or to create a new sales outlet. The prresented tools belong to GIS operations used to process data stored in Spatial Information System resources. These are so-called geoprocessing tools. The article contains several spatial analyses, which results in choosing the optimum location of the distribution point in terms of the defined criteria. The used tools include a spatial intersection and sum. Geocoding and the so-called cartodiagram were also used. The presented analysis can be performed for both the network of authorized retailers within a region, a city or an entire country. The presented tools provide the opportunity to specify the target consumers, areas where they are located and areas of potential consumer concentration. This allows the points of sale in areas with a high probability of finding new customers to be located, which enables the optimal location to be chosen, for example, in terms of access to roads, rail transport, locations of the right area and neighborhood. Spatial analysis tools will also enable the coal company to verify its already existing distribution network.
Go to article

Abstract

A gigantic amounts of data and information on molecules that constitute the very complex cell machinery have been collected, classified and stored in data banks. Although we posses enormous amount of knowledge about the properties and functions of thousands of molecular entities, we are still far from understanding how they do work in a living cell. It is clear now that these molecules (genes, proteins) are not autonomous, that there is no direct linear relation between genotype and phenotype, and that the majority of functions are carried and executed by concerted molecular activity, and that the majority of diseases are multifactorial. A basic property of the matter in a living cell (both normal and pathologic) is an interaction between variety of macromolecules, mainly proteins, genes (DNA) etc. In a process of self-organization they are able to form an active molecular biologic system – a complex, labile and dynamic network which integrity is secured by non-covalent bounds. In this essay some basic properties of network structure and the universal rules that govern them are described. Network or system biology is promising new research approach in biology and medicine.
Go to article

Abstract

A mine cannot function without monitoring systems: environmental, basic mining machinery and equipment. The exploitation of ore in the mine depends heavily on properly functioning machines and mining equipment, and acceptable for the miner technical environmental conditions occurring in underground excavations. The monitoring systems of the technical environment in underground mines are primarily telemetry and gasometry systems. The first part of the article shows the typical structure of gasometry systems operating in the Polish underground mines. The existing provisions include the so-called security systems of the mining plant. The article presents a quantitative summary of the telephone exchange types and count of main telecommunication lines operating in these systems. Monitoring systems of machines and mining equipment are an essential element of the effec-tive management of the mine, because they affect the safe operation and increase time of effi-ciency equipment. The second part of the article shows selected monitoring systems of mining machinery and equipment currently used in the dispatcher rooms of mines. Attention was paid to the monitoring systems, which are only software tools as well as those in which additionally use dedicated IT solutions for these systems, hardware and measuring tools. The table shows the types of monitoring systems and technological configurations used in underground mines, preferred for them.
Go to article

Abstract

Given a linear discrete system with initial state x0 and output function yi , we investigate a low dimensional linear systemthat produces, with a tolerance index ǫ, the same output function when the initial state belongs to a specified set, called ǫ-admissible set, that we characterize by a finite number of inequalities. We also give an algorithm which allows us to determine an ǫ-admissible set.
Go to article

Abstract

A new 4-D dynamical system exhibiting chaos is introduced in this work. The proposed nonlinear plant with chaos has an unstable rest point and a line of rest points. Thus, the new nonlinear plant exhibits hidden attractors. A detailed dynamic analysis of the new nonlinear plant using bifurcation diagrams is described. Synchronization result of the new nonlinear plant with itself is achieved using Integral Sliding Mode Control (ISMC). Finally, a circuit model using MultiSim of the new 4-D nonlinear plant with chaos is carried out for practical use.
Go to article

Abstract

The purpose of this article is to present contemporary climatic changes in their actual scale, and to assess their impact on functioning of urban areas situated on the Polish coast. The results of the analysis of variability of hydro-climatic conditions that occurred in the last 65 years (1951-2015) in the area of the Polish coast suggest that important changes were concerning: (1) temperature of the air, and thickness and length of the occurrence of the snow cover, (2) sea surface temperature, and thickness and length of the occurrence of ice cover, (3) sea level rise during storm surges. It was found, however, that the occurrence of catastrophic fl oods from precipitation in the Tri-City area is not the result of climate change, but it is caused by local conditions. The observed increase of air temperatures, and average sea surface temperatures in the Southern Baltic has generally a positive impact on functioning of coastal cities, and does not need any complex adaptation plans to climate changes. Summer is the only period in which the increase of temperature infl uence cities negatively, due to strengthening the urban heat islands. In this case, the architectural solutions, that require large amounts of energy should be eliminated. In urban planning scale, the solutions helping to cool the space in between buildings should be implemented. Sea level rise in the years 2009-2015, caused by storm surges, should be regarded as a signifi cant change in the climate of the Southern Baltic Sea. Taking these changes into account maps of hazard and flood risk, developed in an ISOK project, should be the basis for detailed records in Study of Conditions and Directions of Spatial Development and local development plans of cities, determining the rules and restrictions of the investment and management in the areas at risk of flooding.
Go to article

Abstract

With the increase in the mass of municipal waste generated, the demand for facilities dealing with their development is increasing. The aim of the research was to determine environmental and anthropogenic factors affecting the location of waste management facilities and an attempt to indicate potential locations for selected waste management facilities in the communes of the Sądecko-Gorlicki region. The scope of work included: a review of existing waste management facilities in the studied region, acquisition of geodatabase for digital data, analysis of the distance between the waste management facilities and environmental or anthropogenic elements, and analysis of potential locations designated in the GIS based on the developed criteria.As a result of spatial analyzes, it was found that in the study area, there are 3 places of potentiallocations for installation of municipal solid waste treatment facilities.
Go to article

Abstract

We study an elegant snap system with only one nonlinear term, which is a quadratic nonlinearity. The snap systemdisplays chaotic attractors,which are controlled easily by changing a system parameter. By using analysis, simulations and a real circuit, the dynamics of such a snap system has been investigated. We also investigate backstepping based adaptive control schemes for the new snap system with unknown parameters.
Go to article

Abstract

The positivity and absolute stability of a class of nonlinear continuous-time and discretetime systems are addressed. Necessary and sufficient conditions for the positivity of this class of nonlinear systems are established. Sufficient conditions for the absolute stability of this class of nonlinear systems are also given.
Go to article

Abstract

In this article, a comparison of economic effectiveness of various heating systems dedicated to residential applications is presented: a natural gas-fueled micro-cogeneration (micro-combined heat and power – μCHP) unit based on a free-piston Stirling engine that generates additional electric energy; and three so-called classical heating systems based on: gas boiler, coal boiler, and a heat pump. Calculation includes covering the demand for electricity, which is purchased from the grid or produced in residential system. The presented analyses are partially based on an experimental investigation. The measurements of the heat pump system as well as those of the energy (electricity and heat) demand profiles in the analyzed building were conducted for a single-family house. The measurements of the μCHP unit were made using a laboratory stand prepared for simulating a variable heat demand. The overall efficiency of the μCHP was in the range of 88.6– 92.4%. The amounts of the produced/consumed energy (electricity, heat, and chemical energy of fuel) were determined. The consumption and the generation of electricity were settled on a daily basis. Operational costs of the heat pump system or coal boiler based heating system are lower comparing to the micro-cogeneration, however no support system for natural gas-based μCHP system is included.
Go to article

Abstract

Hybrid Renewable Energy Systems connected to the traditional power suppliers are an interesting technological solution in the field of energy engineering and the integration of renewable systems with other energy systems can significantly increase in energy reliability. In this paper, an analysis and optimization of the hybrid energy system, which uses photovoltaic modules and wind turbines components connected to the grid, is presented. The system components are optimized using two objectives criteria: economic and environmental. The optimization has been performed based on the experimental data acquired for the whole year. Results showed the optimal configuration for the hybrid system based on economical objective, that presents the best compromise between the number of components and total efficiency. This achieved the lowest cost of energy but with relatively high CO2 emissions, while environmental objective results with lower CO2 emissions and higher cost of energy and presents the best compromise between the number of components and system net present cost. It has been shown that a hybrid system can be optimized in such a way that CO2 emission is maximally reduced and – separately – in terms of reducing the cost. However, the study shows that these two criteria cannot be optimized at the same time. Reducing the system cost increase CO2 emission and enhancing ecological effect makes the system cost larger. However, depends on strategies, a balance between different optimization criteria can be found. Regardless of the strategy used economic criteria – which also indirect takes environmental aspects as a cost of penalties – should be considered as a major criterion of optimization while the other objectives including environmental objectives are less important.
Go to article

Abstract

Which lexical typology does the Italian language have? A comparative study with French – This paper sets out to show the lexical and typological differences between the French and Italian languages. French is the only Romance language without morphology in words. Italian continues to build words while including morphology. This phenomenon can be explained by the diacronic process of deflexivity, which is more advanced in French. The consequence is that French words are more compact and unanalyzable. French is becoming a “neoisolating” language.
Go to article

Abstract

This article focuses on the question of the relation between the subject of The Modern World-System by Immanuel Wallerstein and the theoretical object of worldsystem analysis as a multidisciplinary approach that he proposed for history and the social sciences. The importance of this approach as well as its theoretical deficiencies are shown by examining two unanswered critiques of the first volume of The Modern World-System — one coming from Robert Brenner and the second from Fernand Braudel.
Go to article

Abstract

New optimized 2x2 slotted array antenna is designed using HFSS to operate at 28.1 GHz, using RT6010 substrate with height of 1.6 mm, tangent loss of 0.0023 and dielectric constant of 10.2 and overall dimension of 12x12 mm2, for 5G mobile applications. The 2x2 slotted linear array antenna achieved a high gain of 18.3 dB at 28.1 GHz with 10 dB bandwidth of 1.39 GHz, and with 83.21% of size reduction.
Go to article

Abstract

The application of waste heat from exhaust gas of ship’s main engines has become widely practiced as early as in the 1930s. Thus the increase of ship’s overall efficiency was improved. Nowadays all newly built ships of the 400 gross tonnage and above must have specified energy efficiency design index, which is a measure for CO2 emissions of the ship and its impact on the environment. Therefore, the design of waste heat recovery systems requires special attention. The use of these systems is one of the basic ways to reduce CO2 emissions and to improve the ship’s energy efficiency. The paper describes the ship’s heating systems designed for the use of waste heat contained in the exhaust gas of self-ignition engines, in which the heat carriers are respectively water vapor, water or thermal oil. Selected results of comparative exergy analysis of simplified steam, water and oil heating systems have been presented. The results indicate that the oil heating system is comparable to the water system in terms of internal exergy losses. However, larger losses of exergy occur in the case of a steam system. In the steam system, a significant loss is caused by the need to cool the condensate to avoid cavitation in boiler feed pumps. This loss can in many cases cause the negative heat balance of ship during sea voyage while using only the exhaust gas boilers.
Go to article

Abstract

Embedded software and dedicated hardware are vital elements of the modern world, from personal electronics to transportation, from communication to aerospace, from military to gaming, from medical systems to banking. Combinations of even minor hardware or software defects in a complex system may lead to violation of safety with or even without evident system failure. a major problem that the computing profession faces is the lack of a universal approach to unite the dissimilar viewpoints presented by computer science, with its discrete and mathematical underpinnings, and by computer engineering, which focuses on building real systems and considering spatial and material constraints of space, energy, and time. Modern embedded systems include both viewpoints: microprocessors running software and programmable electronic hardware created with an extensive use of software. The gap between science and engineering approaches is clearly visible in engineering education. This survey paper focuses on exploring the commonalities between building software and building hardware in an attempt to establish a new framework for rejuvenating computing education, specifically software engineering for dependable systems. We present here a perspective on software/hardware relationship, aviation system certification, role of software engineering education, and future directions in computing.
Go to article

Abstract

The paper is aimed at presenting a study of the main limitations and problems influencing the robustness of diagnostic algorithms used in diagnostics of complex chemical processes and to present the selected exemplary solutions of how to increase it. The five major problems were identified in the study. They are associated with: uncertainties of fault detection and reasoning, changes of the diagnosed process structure, delays of fault symptoms formation and multiple faults. A brief description and exemplary solutions allowing increase of the robustness of diagnostic algorithms were given. Proposed methods were selected keeping in mind applicability for the on-line monitoring and diagnostics of complex chemical processes.
Go to article

Abstract

This study provides a systematic review of the existing academic literature describing the key components of eMaintenance. The current literature is reviewed by utilizing a number of academic databases including Scopus, SpringerLink and ScienceDirect, and Google Search is used to find relevant academic and peer-reviewed journal articles concerning eMaintenance. The literature describes eMaintenance as an advanced maintenance strategy that takes advantage of the Internet, information and communication technologies, wireless technologies and cloud computing. eMaintenance systems are used to provide real time analyses based on real time data to offer a number of solutions and to define maintenance tasks. The collection and analysis of appropriate maintenance and process data are critical to create robust ‘maintenance intelligence’ and finally improvements in manufacturing costs, safety, environmental impact, and equipment reliability. This paper describes how the scientific discussion on eMaintenance has expanded significantly during the last decade, creating a need for an up-to-date review. As a conclusion, three research gaps in the area of eMaintenance are identified, including evaluating the benefits of eMaintenance, agreeing on a
Go to article

Abstract

Paper deals with the new localizer GLOP2 designed for detection of the miners trapped in underground hard coal mines. The results of a field test conducted in coal mine BOBREK show that the presented localizer allows for efficient measurement of the distance between a trapped miner and the rescuer in the range of up to 15 m.
Go to article

Abstract

The objective of this study is to investigate the change in partition coefficient with a change in the concentration of the solute in a liquid system consisting of two relatively immiscible solvents. To investigate the changes in the partition coefficients, the data of the partition coefficients at infinite dilution and the ternary Liquid-Liquid Equilibrium (LLE) data at finite concentrations of the solute should be consistent. In this study, 29 ternary systems that are found in literature and for which the partition coefficients at infinite dilution and the ternary LLE data cannot be predicted accurately by the universal quasi-chemical (UNIQUAC) model are identified. On the basis of this model, some consistent and inconsistent ternary systems are introduced. Three inconsistent systems, namely hexane-butanol-water, CCl4 (carbon tetrachloride)-PA (propanoic acid)-water, and hexane-PA-water, are chosen for detailed analysis in this study. The UNIQUAC activity coefficient model is used to represent these data over a range of concentrations. The results show large errors, exhibiting the inability of this model to correlate the data. Furthermore, some ternary systems in which cross behavior of solutes between two phases observed are identified.
Go to article

Abstract

Straw-fired batch boilers, due to their relatively simple structure and low operating costs, are an excellent source of heat for a wide range of applications. A concept prototype of a cogeneration system with a straw-fired batch boiler was developed. The basic assumptions were based on the principles of the Rankine Cycle and the Organic Rankine Cycle systems with certain design modifications. Using the prototype design of a system that collects high-temperature heat from the boiler, studies were performed. The studies involved an analysis of the flue gas temperature distribution in the area of the oil exchanger, a comparison of the instantaneous power of the boiler’s water and oil circuits for different modes of operation, as well as an analysis of the flue gas. In the proposed system configuration where the electricity production supplements heat generation, the power in the oil circuit may be maintained at a constant level of approx. 20-30 kW. This is possible provided that an automatic fuel supply system is applied. Assuming that the efficiency of the electricity generation system is not less than 10%, it will be possible to generate 2-3 kW of electricity. This value will be sufficient, for an on-site operation of the boiler.
Go to article

Abstract

In the paper finite-dimensional time-variable dynamical control systems described by linear stochastic ordinary differential state equations with single time-variable point delay in the control are considered. Using notations, theorems and methods taken directly from deterministic controllability problems necessary and sufficient conditions for different kinds of stochastic relative controllability in a given time interval are formulated and proved. It will be proved that under suitable assumptions relative controllability of a deterministic linear associated dynamical system is equivalent to stochastic relative exact controllability and stochastic relative approximate controllability of the original linear stochastic dynamical system. Some remarks and comments on the existing results for stochastic controllability of linear dynamical systems are also presented.
Go to article

This page uses 'cookies'. Learn more