Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 9
items per page: 25 50 75
Sort by:

Abstract

The instability characteristics of a dielectric fluid layer heated from below under the influence of a uniform vertical alternating current (AC) electric field is analyzed for different types of electric potential (constant electric potential/ electric current), velocity (rigid/free) and temperature boundary conditions (constant temperature/heat flux or a mixed condition at the upper boundary). The resulting eigenvalue problem is solved numerically using the shooting method for various boundary conditions and the solution is also found in a simple closed form when the perturbation heat flux is zero at the boundaries. The possibility of a more precise control of electrothermal convection (ETC) through various boundary conditions is emphasized. The effect of increasing AC electric Rayleigh number is to hasten while that of Biot number is to delay the onset of ETC. The system is more stable for rigid-rigid boundaries when compared to rigid-free and least stable for free-free boundaries. The change of electric potential boundary condition at the upper boundary from constant electric potential to constant electric current is found to instill more stability on the system. Besides, increase in the AC electric Rayleigh number and the Biot number is to reduce the size of convection cells.
Go to article

Abstract

Maintaining railway turnout operability is crucial for ensuring railway transport safety. Electric heating of railway turnouts is a significant technical and economic issue. The classical heating is characterised by high power consumption. For this reason, research is needed to optimise the current system. This paper presents results of a numerical analysis and of experimental researches. The numerical analysis was carried out using the ANSYS software. There was conducted a numerical comparative analysis of energy loss during heating performed using two different heaters. Including the classical method and a heater thermally insulated from a rail. In the first step, heating of a working space filled with a substitute snow model was considered. The snow-covered surface area was held within the working space of the turnout. It was assumed that the snow substitute material had thermal properties approximately the same as real light snow. It was also assumed that the material is in the solid state which would not undergo a phase change. In the next step, a real snow model that included the phase change process was taken into account. The energy efficiency and heat distribution in the turnout have been analysed and compared. The experimental researches were carried out in a physical model. The results showed that the use of a contactless heater results in creating a larger area over which emitted heat affected snow in the working space. Consequently, more snow was melted around the contactless heater than the classic one. This experimental observation supported the results of the numerical analyses presented previously.
Go to article

Abstract

This paper describes the application of the skull melting method for an artificial generation of particulate material of inorganic compounds like CsOH, NaOH, SnO2 and UO2. The skull melting process is analyzed analytically. Thereby the electromagnetic field is calculated by a one dimensional time harmonic model. Thermal losses are estimated by simple analytical formulas. Finally an electromagnetic thermal field coupling is performed to calculate the temperature distribution inside the crucible, considering transient thermal effects. The skull melting process is simulated for the example of UO2. Under consideration of the given material properties it is shown that the skull melting method can be applied to fuse UO2.
Go to article

Abstract

The calculation results of the static field parameters for permanent magnet linear synchronous motor have been presented in this work. The influence of the construction temperature on the parameters has been analyzed mathematically. Models for magnetic and temperature fields determination have been formulated. Two kinds of permanent magnets (NdFeB and SmCo) have been considered. The distribution of the thermal field has been obtained using the finite element method (FEM).
Go to article

Abstract

A vertical cut at the mid-depth of the 15-ton forging steel ingot has been performed by curtesy of the CELSA – Huta Ostrowiec plant. Some metallographic studies were able to reveal not only the chilled undersized grains under the ingot surface but columnar grains and large equiaxed grains as well. Additionally, the structural zone within which the competition between columnar and equiaxed structure formation was confirmed by metallography study, was also revealed. Therefore, it seemed justified to reproduce some of the observed structural zones by means of numerical calculation of the temperature field. The formation of the chilled grains zone is the result of unconstrained rapid solidification and was not subject of simulation. Contrary to the equiaxed structure formation, the columnar structure or columnar branched structure formation occurs under steep thermal gradient. Thus, the performed simulation is able to separate both discussed structural zones and indicate their localization along the ingot radius as well as their appearance in term of solidification time.
Go to article

Abstract

Postharvest processing of grain is an important step in the overall grain production process. It makes possible not only quantitative and qualitative preservation of the harvest, but also ensures maximum profit from its sale at the most favorable market conditions. Convective heat treatment (drying, cooling) guarantees commercial harvest conservation, prevents its loss, and in some cases improves the quality of the finished product. The necessity of intensification and automation of technological processes of postharvest grain processing requires the development of methods of mathematical modeling of energy-intensive processes of convective heat treatment. The determination and substantiation of optimum modes and parameters of equipment operation to ensure the preservation of grain quality is possible only when applying mathematical modeling techniques. In this work, a mathematical model of particulate material drying is presented through a system of differential equations in partial derivatives of which the variable in time and space relationship between heat and mass transfer processes in the material and a drying agent is reflected. The aim of the research was to determine the dynamics of the interrelated fields of unsteady temperature and moisture content of the material and the drying agent on the basis of mathematical models of heat and mass transfer in the layer of particulate material in convective heat approach or heat retraction. The implementation of the mathematical model proposed in the standard mathematical set allows analyzing efficiency of machines and equipment for the convective heat treatment of particulate agricultural materials in a dense layer, according the determinant technological parameters and operating modes.
Go to article

Abstract

In this paper, a three-air-gapped structure of a ferrite core for a resonant inductor is proposed. The electromagnetic and thermal field models are built using a 3D finite element method. Compared with the conventional signal-air-gapped structure of a ferrite core, the simulation and analysis results show that the proposed three-air-gapped ferrite core resonant inductor can reduce eddy-current loss and decrease temperature rise. In addition, the optimal position of air-gapped is presented.
Go to article

Abstract

The transient thermal model of the permanent magnet linear actuator (PMLA) has been considered. The characteristics of heating have been calculated including the main subdomains of the actuator. The carcasses from various materials have also been considered. The calculations have been verified experimentally and a good conformity was obtained.
Go to article

Abstract

Some metallographic studies performed on the basis of the massive forging steel static ingot, on its cross-section, allowed to reveal the following morphological zones: a/ columnar grains (treated as the austenite single crystals), b/ columnar into equiaxed grains transformation, c/ equiaxed grains at the ingot axis. These zones are reproduced theoretically by the numerical simulation. The simulation was based on the calculation of both temperature field in the solidifying large steel ingot and thermal gradient field obtained for the same boundary conditions. The detailed analysis of the velocity of the liquidus isotherm movement shows that the zone of columnar grains begins to disappear at the first point of inflection and the equiaxed grains are formed exclusively at the second point of inflection of the analyzed curve. In the case of the continuously cast brass ingots three different morphologies are revealed: a/ columnar structure, b/ columnar and equiaxed structure with the CET, and c/ columnar structure with the single crystal formation at the ingot axis. Some forecasts of the temperature field are proposed for these three revealed morphologies. An analysis / forecast of the behavior of the operating point in the mold is delivered for the continuously cast ingot. A characteristic delay between some points of breakage of the temperature profile recorded at the operating point and analogous phenomena in the solidifying alloy is postulated.
Go to article

This page uses 'cookies'. Learn more