Applied sciences

Chemical and Process Engineering: New Frontiers

Content

Chemical and Process Engineering | 2019 | vol. 40 | No 2

Download PDF Download RIS Download Bibtex

Abstract

The study concerns modeling and simulation of the growth of biofilms with heterogeneous structures with a discrete mathematical model based on theory of cellular automata. The article presents two-dimensional density distributions of biofilms for microbial processes: oxidation of ammonium by Nitrosomonas europaea bacteria and glucose utilization by Pseudomonas aeruginosa bacteria. The influence of limiting substrate concentration in the liquid phase on biofilm structure was determined. It has been shown that the value of death rate coefficient of microorganisms has the qualitative and quantitative influence on the density and porosity of the biofilm.

Go to article

Authors and Affiliations

Szymon Skoneczny
Download PDF Download RIS Download Bibtex

Abstract

Twenty-eight two-, three-, four-, and five-component amine mixtures have been evaluated as possible activators of CO2 absorption into aqueous carbonate/bicarbonate solutions. Measurements were per- formed using a pressure autoclave with a sparger at conditions close to industrial ones. On the basis of these results, a formula for a new, more efficient amine activator named INS13 was developed. The activator was tested both in a pilot plant and on an industrial scale in an ammonia plant producing 300 tons/day of ammonia. Activator INS13 was applied in a number of ammonia plants in Poland and abroad.

Go to article

Authors and Affiliations

Grzegorz Bińczak
Ryszard Pohorecki
Władysław Moniuk
Cezary Możeński
Download PDF Download RIS Download Bibtex

Abstract

Typically applied static (i.e. non-agitated) cultures do not provide sufficient conditions for efficient propagation of suspended non-adherent cells, in general. Feasibility of small-scale wave-type agitated single-use bioreactors for gentle agitation underlies applicability of such systems for scaling-up of fragile biomass of animal cells. The basic aim of the study was to compare the results of non-adherent HL-60 cell propagation performed referentially as the batch culture in typical static (i.e. non-agitated) disposable culture flasks (50 cm3 of culture medium) and in ReadyToProcess WAVETM25 bioreactor system (GE Healthcare) equipped with disposable culture bag (300 cm3 of culture medium) subjected to continuous wave-type agitation. The density and viability of HL-60 cells were significantly higher for the bioprocess subjected to wave-type agitation, than in the reference static culture. The values of the specific rate of glucose consumption per cell (rglc=cell) exhibited by HL-60 cells maintained in the system with continuous wave-type agitation was significantly lower (i.e. up to more than 42%) than the values noted for the static culture, for exactly the same time-points of two compared cultures. The results of the studies undoubtedly and comprehensively confirmed the applicability of the studied disposable bioreactor with wave-induced agitation as the right platform for proceeding the propagation of non- adherent HL-60 cells and for providing the culture conditions required by HL-60 cells for sustainable metabolism.

Go to article

Authors and Affiliations

Kamil Wierzchowski
Iwona Grabowska
Maciej Pilarek
Download PDF Download RIS Download Bibtex

Abstract

This paper analyses the influence of the applied microwave power output on the intensification of drying in the context of process kinetics and product quality. The study involved testing samples of beech wood (Fagus sylvatica L.). Wood samples were dried in the microwave chamber at: 168 W, 210 W, 273 W, 336 W and 378 W power output level. For comparison, wood was dried convectively at 40 ◦C and 87% air relative humidity. The analysis of drying process kinetics involved nonlinear regression employing the Gompertz model. Dried samples were subjected to static bending tests in order to specify the influence of the applied microwave power on modulus of elasticity (MOE) and modulus of rapture (MOR). The obtained correlations of results were verified statistically. Analysis of drying kinetics, strength test results and Tukey’s test showed that the applied microwaves of a relatively low level significantly shortened the drying time, but did not cause a reduction in the final quality of dried wood, compared with conventional drying.

Go to article

Authors and Affiliations

Kinga Rajewska
Anna Smoczkiewicz-Wojciechowska
Jerzy Majka
Download PDF Download RIS Download Bibtex

Abstract

The presence of inorganic elements in solid fuels is not only considered a direct source of problems in the furnace but is also connected with the release of pollutants into air during combustion. This article focuses on the sintering characteristics of biomass and coal ashes, in particular on the leaching processes, and their impact on the tendency to sinter ash. Biomass and coal ash with high alkali metal concentration can deposit in boiler sections and cause severe operating problems such as slagging, fouling and corrosion of boiler and heat exchanger surface, limiting heat transfer. Two biomass types and one coal ash with different origin and different chemical compositions were investigated. A sequential leaching analysis was employed in this study to elucidate the modes of occurrence of metals that can transform into fuel extract. Sequential leaching analysis was conducted as a two-step process: using distilled water in the first step and acetic acid in the second step. The chemical composition of ashes, before and after each step of the leaching processwas studied using ICP-OES method. The standard Ash Fusion Temperature (AFTs) technique was also employed to assess the sintering tendency of the tested samples. It was observed that the presence of key elements such as sodium, potassium, magnesium and sulphur (elucidated in the leaching process) plays a significant role in sintering process. The sintering tendency enhances when the concentration of these elements increases.

Go to article

Authors and Affiliations

Arkadiusz Szydełko
Dorota Nowak-Woźny
Bartosz Urbanek
Laura González Valdés
Wiesław Rybak
Download PDF Download RIS Download Bibtex

Abstract

The flow of the investigated fluid in a measuring system of a rheometer – a capillary or a slit between rotating parts – may be disturbed by anisotropic behavior of the fluid near the wall. This phenomenon, so-called wall slip, often takes place in concentrated suspensions and solutions of linear polymers and introduces experimental errors to measurement results. There are methods of correction of these errors in the case of capillary and coaxial cylinders measuring systems. In the cone and plate system the correction seems to be more difficult because the width of the gap between cone and plate changes along the radius and thus the influence of the wall slip on the shear stress varies along the radius in an unpredictable and complicated manner. This dependency of the shear stress on the distance from the axis underlies the presented method of correction of experimental results obtained in the cone and plate system. The method requires several series of measurements of shear stress vs. shear rate performed using one measuring set, at various degrees of filling the gap.

Go to article

Authors and Affiliations

Tomasz Kiljański
Download PDF Download RIS Download Bibtex

Abstract

This paper discusses the influence of the direction of applied deformation on the ability to gelation of thermosensitive chitosan hydrogels. The application of the shear rate equal in value to the classically performed oscillatory measurements leads to significantly different shapes of experimental curves. It was found that the type of mechanically applied deformation has a significant impact on the gelation ability of colloidal chitosan solutions and conditions of sol-gel phase transition. Simple shear leads to a phase transition at a lower temperature or in a shorter time compared to oscillatory tests. Moreover, based on the final values of dynamic viscosity in rotational measurements, it was found that stronger crosslinking of the polymer structure was observed.

Go to article

Authors and Affiliations

Anna Rył
ORCID: ORCID
Piotr Owczarz
ORCID: ORCID
Download PDF Download RIS Download Bibtex

Abstract

A detailed comparison of catalytic properties of two different ruthenium-based catalysts in the reaction of homogeneous hydrogenation of acetophenone was performed. Additionally, methods of synthesis of both catalysts were tested and optimized in order to achieve the best possible quality and purity of the final catalysts.

NMR analysis was used to analyze and identify the composition of ruthenium compounds and gas chromatography was used to analyze the conversion rate of hydrogenation reactions.

It was determined that RuCl2(PPh3)3 obtained with a modified method described by Shaw’s group (Shawet al., 2007) had the best catalytic properties in the reaction performed under conditions described in Liang Wang’s publication (Wang et al., 2014). It was also determined that for concentration ratio of substrate to RuCl2(PPh3)3 amounting to 250:1 the conversion rate was much higher than that of the reaction performed with a double dose of the catalyst. Results of experiments also show that samples of the post-reaction solution should be analyzed right after the reaction, because even if they are stored in low temperature the amount of product can change up to 3–5% compared to the base sample and this change is not predictable.

These findings have significant implications for further research of the reaction of homogeneous transfer hydrogenation of ketones. With the right catalysts and methods of their synthesis other parameters of this reaction can be optimized. The most important one is a change of solvent from isopropyl alcohol to a less toxic substance like water. This may increase the value of the reaction in green chemistry and chemical industry.

Go to article

Authors and Affiliations

Filip Mikołajczyk
Kamil Kamiński
Download PDF Download RIS Download Bibtex

Abstract

The aim of the paper was to develop determination methods of sedimentation characteristics using PIV image anemometry and suspension image analysis. Two methods of the investigation of sed- imentation process based on visualization techniques were developed. In the first one, using PIV method, vector fields of the velocity of settling particles are determined and then average particle velocities are calculated to establish the so called sedimentation dynamics curve. In the second one, the methods of suspension image analysis are utilized to determine the positions of the upper dis- continuity and to establish the sedimentation curve. Laboratory research on the sedimentation of agalit particles suspended in glycerine was conducted (using PIV method). Additionally, industrial research on the sedimentation of water-absorbing granular material used after the first carbonation (carbonation I) was conducted in a sugar factory (using the second method). The research consisted of photographic registration of images of the settling suspension by means of the time-lapse photog- raphy technique. A laboratory study was conducted for four values of the volume concentration of agalit particles in glycerine (0.5; 1.0; 1.5 and 2.0 vol%). The research methodology, the scope of the conducted measurements and sample research results together with conclusions are presented in this paper.

Go to article

Authors and Affiliations

Witold Suchecki
Download PDF Download RIS Download Bibtex

Abstract

The paper presents results of the field tests on membrane biogas enrichment performed with the application of mobile membrane installation (MMI) with the feed stream up to 10 Nm3/h. The mobile installation equipped with four hollow fibre modules with polyimide type membranes was tested at four different biogas plants. Two of them were using agricultural substrates. The third one was constructed at a municipal wastewater plant and sludge was fermented in a digester and finally in the fourth case biogas was extracted from municipal waste landfill site. Differences in the concentration of bio-methane in feed in all cases were observed and trace compounds were detected as well. High selectivity polyimide membranes, in proper module arrangements, can provide a product of high methane content in all cases. The content of other trace compounds, such as hydrogen sulphide, water vapour and oxygen on the product did not exceed the values stated by standard for a biogas as a vehicle fuel. The traces of hydrogen sulphide and water vapour penetrated faster to the waste stream enriched in carbon dioxide, which could lead to further purification of the product – methane being hold in the retentate (H2O > H2S > CO2 > O2 > CH4 > N2). In the investigated cases, when concentration of N2 was low and concentration of CH4 higher than 50%, it was possible to upgrade methane to concentration above 90% in a two-stage cascade.

To performsimulation ofCH4 andCO2 permeation through polyimide membrane,MATLABwas used. Simulation program has included permeation gaseous mixture with methane contents as observed at field tests in the range of 50 and 60% vol. The mass transport process was estimated for a concurrent hollow fibre membrane module for given pressure and temperature conditions and different values of stage cut. The obtained results show good agreement with the experimental data. The highest degree of methane recovery was obtained with gas concentrating in a cascade with recycling of the retentate.

Go to article

Authors and Affiliations

Andrzej Grzegorz Chmielewski
Agata Urbaniak
Jacek Palige
Otton Roubinek
Katarzyna Wawryniuk
Andrzej Dobrowolski

Instructions for authors

All manuscripts submitted for publication in Chemical and Process Engineering: New Frontiers must comprise a description of original research that has neither been published nor submitted for publication elsewhere.

The content, aim and scope of the proposals have to comply with the main topics of the journal, i.e. discuss at least one of the four main areas, namely:
• New Advanced (Nano) Materials
• Environment & Water Processing (including circular economy)
• Biochemical & Biomedical Engineering (including pharmaceuticals)
• Climate & Energy (including energy conversion & storage, electrification, decarbonization)

Chemical and Process Engineering: New Frontiers publishes: i) experimental and theoretical research papers, ii) short communications, iii) critical reviews, and iv) perspective articles. Each publication form is peer-reviewed by at least two independent referees.

New Submissions

Manuscripts are submitted for publication via Editorial System. When writing a manuscript, you may choose to submit it as a single Word file to be used in the refereeing process. The manuscript needs to be written in a clear way. The minimum requirements are:
• Please use clear fonts, at least 12 points large, with at least 1.5-line spacing.
• Figures should be placed in relevant places within the manuscript. All figures and tables should be numbered and provided with appropriate caption and legend, if necessary.


Language requirements

• Use Simple Past to talk about your experiment and your results as they were finished before you wrote the paper. Use Simple Past to describe what you did.
Example: Two samples were taken. Temperature increased to 200K at the end of the process.
• Use Simple Present to refer to figures and tables.
Example: Table 2 shows nitrogen concentration changes in the process.
• Use Simple Present to talk about your conclusions. You move here from describing your results to stating what is generally true.
Example: The process is caused by changes of nitrogen concentration.
• Capitalise words like ‘Table 2’, ‘Equation 11’.
• If a sentence is longer than three lines, break down your writing into logically divided parts (paragraphs). Start a new paragraph to discuss a new concept.
• Check noun/verb agreement (singular/plural).
• It is fine to choose either British or American English but you should avoid mixing the two.
• Avoid empty language (it is worth pointing out that, etc.).



Revised Submission

After the first revision, authors will be requested to put their paper in the correct format, using the below guidelines and template for articles.


Manuscript outline

1. Header details
a. Title,
b. Names (first name and further initials) and surnames of authors,
c. Institution(s) (affiliation),
d. Address(es) of authors,
e. ORCID number of all authors.
f. Information about the corresponding author: name and surname, email address.

2. Abstract – should contain a short summary of the proposed paper. In the maximum of 200 words the authors should present the main assumptions, results and conclusions drawn from the presented study.

3. Keywords – up to 5 characteristic keyword items should be provided.

4. Text
a. Introduction. In this part, the rationale for research and formulation of the scientific problem should be included and supported by a concise review of recent literature.
b. Main text. It should contain all important elements of the scientific investigations, such as presentation of experimental setup, mathematical models, results and their discussion. This part may be divided into the following sections: Methods, Results, Discussion.
c. Conclusions. The major conclusions can be put forward in a concise style in a separate chapter. A presentation of conclusions from the reported research work accompanied by a short commentary is also acceptable.
d. Figures: drawings, diagrams and photographs can be in colour and should be located in appropriate places in the manuscript. Their form should be of a vector or raster type with the minimum resolution of 900 dpi. In addition, all figures, including drawings, graphs and photos should be uploaded in a separate file via Editorial System in one of the following formats: bmp, tiff, jpg or eps. For editorial reasons, graphic elements created with MS Word or Excel will not be accepted. They should be saved as image files in the source program. Screen shots will not be accepted. The basic font size of letters used in figures should be at least 10 pts after adjusting graphs to the final size.
e. Tables should be made according to the format shown in the template.
f. All figures and tables should be numbered and provided with an appropriate caption and legend, if necessary. They have to be properly referenced to and commented in the text of the manuscript.

5. List of symbols should be accompanied by their units

6. Acknowledgements may be included before the list of literature references

7. Literature citations
The method of quoting literature source in the manuscript depends on the number of its authors:
single author – their surname and year of publication should be given, e.g. Marquardt (1996) or (Marquardt, 1996),
two authors – the two surnames separated by the conjunction “and” with the publication year should be given, e.g. Charpentier and McKenna (2004) or (Charpentier and McKenna, 2004),
three and more authors – the surname of the first author followed by the abbreviation “et al.” and year of publication should be given, e.g. Bird et al. (1960) or (Bird et al., 1960).

In the case of citing more sources in one bracket, they should be listed in alphabetical order using semicolon for separation, e.g. (Bird et al., 1960; Charpentier and McKenna, 2004; Marquardt, 1996). Should more citations of the same author(s) and year appear in the manuscript then letters “a, b, c, ...” should be successively applied after the publication year.

Bibliographic data of the quoted literature should be arranged at the end of the manuscript in alphabetical order of surnames of the first author. It is obligatory to indicate the DOI number of those literature items, whose numbers have already been assigned. Journal titles should be specified by typing their right abbreviations or, when in doubts, according to the Science and Engineering Journal Abbreviations.

Examples of citation for:

Articles
Charpentier J. C., McKenna T. F., 2004. Managing complex systems: some trends for the future of chemical and process engineering. Chem. Eng. Sci., 59, 1617-1640. DOI: 10.1016/j.ces.2004.01.044.
Information from books (we suggest adding the page numbers where the quoted information can be found)
Bird R. B., Stewart W.E., Lightfood E.N., 2002. Transport Phenomena. 2nd edition, Wiley, New York, 415-421.
Chapters in books
Hanjalić K., Jakirlić S., 2002. Second-moment turbulence closure modelling, In: Launder B.E., Sandham N.D. (Eds.), Closure strategies for turbulent and transitional flows. Cambridge University Press, Cambridge, 47-101.
Conferences
ten Cate A., Bermingham S.K., Derksen J.J., Kramer H.M.J., 2000. Compartmental modeling of an 1100L DTB crystallizer based on Large Eddy flow simulation. 10th European Conference on Mixing. Delft, the Netherlands, 2-5 July 2000, 255-264.



Cover letter


Authors are kindly asked to provide a cover letter which signifies the novelty and most important findings of the manuscript as well as the significance to the field.


Author contributions

During submission, authors will be asked to provide the individual contributions to the paper using the relevant CRediT roles: Conceptualization; Data curation; Formal analysis; Funding acquisition; Investigation; Methodology; Project administration; Resources; Software; Supervision; Validation; Visualization; Roles/Writing - original draft; Writing - review & editing.


Suggested Reviewers

Authors are kindly requested to include a list of 4 potential reviewers for their manuscript, with complete contact information. Suggested reviewers may not reside in the same country as the corresponding author and remain subject to the Editors' discretion in appointing manuscripts for review.


Payments

Starting from 2014 a principle of publishing articles against payment is introduced, assuming non-profit making editorial office. According to the principle, authors or institutions will have to cover the expenses amounting to 1500 PLN netto (excl. VAT) per published article. The above amount will be used to supplement the limited financial means received from the Polish Academy of Sciences for the editorial and publishing expenses. The method of payment will be indicated in an invoice sent to the authors or institutions after acceptance of their manuscripts to be published.

Publication Ethics Policy

ETHICAL PRINCIPLES

Editors of the "Chemical and Process Engineering: New Frontiers" pay attention to maintain ethical standards in scientific publications and undertake any possible measure to counteract neglecting the standards. Papers submitted for publication are evaluated with respect to reliability, conforming to ethical standards and the advancement of science. Principles given below are based on COPE's Best Practice Guidelines for Journal Editors, which may be found at:
http://publicationethics.org/files/u2/Best_Practice.pdf

Authors’ duties

Authorship
Authorship should be limited to persons, who markedly contributed to the idea, project, realization and interpretation of results. All of them have to be listed as co-authors. Other persons, who affected some important parts of the study should be listed or mentioned as co-workers. Author should be certain that all co-authors were enlisted, saw and accepted final version of the paper and agreed upon its publication.

Disclosure and conflict of interests
Author should disclose all sources of financing of his/her study, the input of scientific institutions, associations and other subjects and all important conflicts of interests that might affect results and interpretation of the study.

Standards in reporting
Authors of papers based on original studies should present precise description of performed work and objective discussion on its importance. Source data should be accurately presented in the paper. The paper should contain detailed information and references that would enable others to use it. False or intentionally not true declarations are not ethical and are not accepted by the editors.

Access to and storage of data
Authors may be asked for providing raw data used in the paper for editorial assessment and should be prepared to store them within the reasonable time period after publication.

Multiple, unnecessary and competitive publications
As a rule author should not publish papers describing the same studies in more than one journal or primary publication. Submission of the same paper to more than one journal at the same time is not ethical and prohibited.

Confirmation of sources
Author should cite papers that affected the creation of submitted manuscript and every time he/she should confirm the use of other authors’ work.

Important errors in published papers
When author finds an important error or inaccuracy in his/her paper, he/she is obliged to inform Editorial Office about this as soon as possible.

Originality and plagiarism
Author may submit only original papers. He/she should be certain that the names of authors referred to in the paper and/or fragments of their texts are properly cited or mentioned.

Ghostwriting
Ghost writing/guest authorship are manifestation of scientific unreliability and all such cases will be revealed including notification of appropriate subjects. Signs of scientific unreliability, especially violation of ethical principles in science will be documented by the Editorial Office.


Duties of the Editorial Office


Editors’ duties
Editors know the rules of journal editing including the procedures applied in case of uncovering non-ethical practices.

Decisions on publication
Editor-in Chief is obliged to apply present legal status as to defamation, violation of author’s rights and plagiarism and bears the responsibility for decisions. He/she may consult thematic editors and/or referees in that matter.

Selection of referees
Editorial Office provides appropriate selection of referees and takes care about appropriate course of peer –reviewing (the review has to be substantive).

Confidentiality
Every member of editorial team is not allowed to disclose information about submitted paper to any person except its author, referees, other advisors and editors.

Discrimination
To counteract discrimination the Editorial Office obeys the legally binding rules.

Disclosure and conflict of interests
Not published papers or their fragments cannot be used in the studies of editorial team or ref-erees without written consent of the author.


Referees' duties

Editorial decisions

Referee supports Editor-in-Chief in taking editorial decisions and may also support author in improving the paper.

Back information
In case a selected referee is not able to review the paper or cannot do it in due time period, he/she should inform secretary of the Editorial Office about this fact.

Objectivity standards
Reviews should be objective. Personal criticism is inappropriate. Referees should clearly ex-press their opinions and support them with proper arguments.

Confidentiality
All reviewed papers should be dealt with as confidential. They should not be discussed or revealed to persons other than the secretary of the Editorial Office.

Anonymity
All reviews should be made anonymously and the Editorial Office does not disclose names of the authors to referees.

Disclosure and conflict of interests
Confidential information or ideas resulting from reviewing procedure should be kept secret and should not be used to gain personal benefits. Referees should not review papers, which might generate conflict of interests resulting from relationships with the author, firm or institution involved in the study.

Confirmation of sources
Referees should indicate publications which are not referred to in the paper. Any statement that the observation, source or argument was described previously should be supported by appropriate citation. Referee should also inform the secretary of the Editorial Office about significant similarity to or partial overlapping of the reviewed paper with any other published paper and about suspected plagiarism.



This page uses 'cookies'. Learn more